manualshive.com logo in svg

Intel 81341, Developer'S Manual

The Intel 81341 Developer's Manual is a comprehensive guide to understanding and utilizing the capabilities of this powerful product. Available for free download on our website, this manual provides detailed instructions and information to help developers maximize the potential of the Intel 81341. Download it from manualshive.com.

Share
Download
background image

Intel

®

 81341 and 81342—PMON Unit

Intel

®

 81341 and 81342 I/O Processors

Developer’s Manual

December 2007

970

Order Number: 315037-002US

14:12

000b

Command Trigger Source Select (CTSS)

This field expands the Event Selection Codes in the Command trigger field to 1 of 8 ports, which share 

the same codes. Normally driven to 000, unless another source of the same type is to be selected. For 

81341 and 81342, there are 8 different sources for SAS/SATA events, so setting these bits as “000” 

choose an event from SAS/SATA Port-0, and setting these bits as “001” choose an event from SAS/

SATA Port-1, etc.

11:0

000h

Command Trigger (CT)

This field contains the Event Selection Code (ESC) that the unit is required to detect before executing 

the opcode. The previously programmed opcode continues to execute until this command trigger is 

detected.

The ESC of 000h (the default value) is a special case, This special ESC causes the command to be 

triggered immediately upon being written to the command register. The special command trigger also 

causes that command to be executed (triggered) once and only once. All other (non-0) ESCs cause the 

command to be re-executed every time the trigger is detected. Refer to the Event tables for valid 

values. For the Stop, Start, and Reset opcodes, re-executing every time the trigger is detected is 

meaningless. For other opcodes, care must be taken to prevent the CT from producing undesirable 

behavior. The only opcodes that are anticipated as being useful with continual triggering include the 

Restart functionality which behavior is necessary to facilitate gathering of histogram data at hardware 

speeds.

Only one trigger can occur per core clock. When the trigger source clock is running faster than the core 

clock and more than one trigger event occurs per core clock, these additional triggers are dropped.

See the Event Table for valid values.

Table 609. PMON Command Register 0-7 - PMON_CMD[0:7] (Sheet 4 of 4)

Bit

Default

Description

PCI

IOP

Attributes

Attributes

28

24

20

16

12

8

4

0

31

rv

rv

rv

rv

rv

rv

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

Attribute Legend:

RV = Reserved

PR = Preserved

RS = Read/Set

RW = Read/Write

RC = Read Clear

RO = Read Only

NA = Not Accessible

 Register Offset

PMON

_CMD0

PMON

_CMD1

PMON

_CMD2

PMON

_CMD3

PMON

_CMD4

PMON

_CMD5

PMON

_CMD6

PMON

_CMD7

+000h

+010h

+020h

+030h

+040h

+050h

+060h

+070h

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 81341

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Brand: Baracoda Pages: 42
Omnia Volt Quick Start Installation Manual preview
Volt
Brand: Omnia Pages: 6
Lantronix SISPM1040-582-LRT Quick Start Manual preview
SISPM1040-582-LRT
Brand: Lantronix Pages: 2
Lantronix SDS1101 Quick Start Manual preview
SDS1101
Brand: Lantronix Pages: 7
Harmonic XOS User Manual preview
XOS
Brand: Harmonic Pages: 56
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
Renesas RSKH836079 Quick Start Manual preview
RSKH836079
Brand: Renesas Pages: 6
LSI MegaRAID SATA 300-4XLP Quick Installation Manual preview
MegaRAID SATA 300-4XLP
Brand: LSI Pages: 3
Daedalon EC-33 Instruction Manual preview
EC-33
Brand: Daedalon Pages: 6
Qlogic QLE7xxx Series Quick Start Manual preview
QLE7xxx Series
Brand: Qlogic Pages: 8
ZALMAN ZM-RF1 User Manual preview
ZM-RF1
Brand: ZALMAN Pages: 5
4gon RouterBOARD 411R Quick Start Manual preview
RouterBOARD 411R
Brand: 4gon Pages: 2
ZyXEL Communications ZyXEL ZyAIR B-120 Quick Installation Manual preview
ZyXEL ZyAIR B-120
Brand: ZyXEL Communications Pages: 20
ST X-NUCLEO-EEPRMA1 User Manual preview
X-NUCLEO-EEPRMA1
Brand: ST Pages: 22
AMD Geode LX 800 User Manual preview
Geode LX 800
Brand: AMD Pages: 27
EXAGATE SYSGuard 6001 Quick Installation Manual preview
SYSGuard 6001
Brand: EXAGATE Pages: 7
Intel SRCU31L Quick Start Manual preview
SRCU31L
Brand: Intel Pages: 20
Extron electronics VERSATOOLS MTP User Manual preview
VERSATOOLS MTP
Brand: Extron electronics Pages: 19

Brands by name

Popular brands

Load more brands