Intel 81341 Developer'S Manual Download Page 877

Page: 877 / 1056

Intel

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

877

SMBus Interface Unit—Intel

81341 and 81342

14.4.5

SMBus Controller ADDR1 Register Number — SM_ADDR1

This register should be programmed with the upper address bits (bits [11:8]) of the

81341 and 81342 ignores bit [7:4] of this register. The Status Register should be

checked to make sure that there is not a command currently in progress, before writing

to this register. Writing to this register when the 'Busy' bit in the Status Register is

asserted has indeterminate effects. When accessing memory space, ADDR1 provides

bits [15:8] of the memory address offset.

14.4.6

SMBus Controller ADDR0 Register Number — SM_ADDR0

This register should be programmed with the lower address bits (bits [7:0]) of the

The Status Register should be checked to make sure that there is not a command

currently in progress, before writing to this register. Writing to this register when the

'Busy' bit in the Status Register is asserted has indeterminate effects. When accessing

memory space, SM_ADDR0 provides bits [7:0] of the memory address offset.

Table 555. SMBus Controller ADDR1 Register Number — SM_ADDR1

Bit

Reset

Description

07:00

00H

Upper Number (UNUM): Indicates the upper 4 bits (bits [11:8] of the register number to access for 4-

KByte configuration space. Bits [7:4] of this registers is ignored by 81341 and 81342. For memory

access, this register provides bits [15:8] of the memory address offset.

Table 556. SMBus Controller ADDR0 Register Number — SM_ADDR0

Bit

Reset

Description

07:00

00H

Lower Number (LNUM): Indicates the lower 8 bits (bits [7:0] of the register number to access for 4-

KByte configuration space. For memory access, this register provides bits [7:0] of the memory address

offset.

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands