Intel 81341 Developer'S Manual Download Page 968

Page: 968 / 1056

Intel

81341 and 81342—PMON Unit

Intel

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

968

Order Number: 315037-002US

Threshold Indicator Enable (THIE)

0 = No indication provided when threshold condition is true except for setting the Threshold Indicator

(TI) status bit.

1 = When the threshold condition is true, the counter sets the status bit and possibly assert the

PMON

OUT pin or enable the generation of an interrupt. This is controlled by the

PMON

OUT Enable

and Interrupt Enable respectively. Interrupts are driven directly off of the status bits, whereas the

PMON

OUT pin is driven directly from the condition.

23:21

000b

Condition Code (CC)

This field contains the code that indicates what type of threshold compare is done between the counter

and the data register. For all non-0 values of this field, the counter’s data register contains the

threshold value. The outcome of this compare generates a threshold event and potentially an interrupt

when that capability is enabled.

• Bit 23 is for less than (<)

• Bit 22 is for equal (=)

• Bit 21 is for greater than (>)

Select the proper bit mask for desired threshold condition:

• 000 = False (no threshold compare)

• 001 = Greater Than

• 010 = Equal

• 011 = Greater Than or Equal

• 100 = Less Than

• 101 = Not Equal

• 110 = Less Than or Equal

• 111 = True (always generate threshold event)

Select ALL Counters (SAC). This bit controls how the opcode in bits 19:16 is applied to all counters. The

rest of the

PMON

_CMD register is not affected by the setting of this bit.

0 = The opcode is applied only to the counter associated with this command register.

1 = The opcode is applied to ALL counters. This means that every command register is written to with

the same value that was written to this particular command register. This is particularly useful for

resetting all counters with a single command or starting or stopping all counters simultaneously.

Note:

This bit is only valid in Command Register 0 and has no effect in non-0 command registers.

“Globally” executed commands (by setting this bit in Command Register 0) always override

“locally” executed commands.

Table 609. PMON Command Register 0-7 - PMON_CMD[0:7] (Sheet 2 of 4)

Bit

Default

Description

PCI

IOP

Attributes

Attribute Legend:

RV = Reserved

PR = Preserved

RS = Read/Set

RW = Read/Write

RC = Read Clear

RO = Read Only

NA = Not Accessible

PMON

_CMD0

PMON

_CMD1

PMON

_CMD2

PMON

_CMD3

PMON

_CMD4

PMON

_CMD5

PMON

_CMD6

PMON

_CMD7

+000h

+010h

+020h

+030h

+040h

+050h

+060h

+070h

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands