Intel 81341 Developer'S Manual Download Page 41

Page: 41 / 1056

Intel

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

Contents—Intel

81341 and 81342

652 DDR SDRAM Memory Controller ..............................................................................1032

653 I/O Pad Control Base Address Offset........................................................................1033

654 I/O Pad Control Unit..............................................................................................1034

655 UART 0-1 Offset....................................................................................................1036

656 UART...................................................................................................................1036

657 GPIO Offset..........................................................................................................1037

658 GPIO...................................................................................................................1037

659 I

C 0-2 Offset.......................................................................................................1037

660 I2C Unit...............................................................................................................1037

661 Messaging Unit Offset............................................................................................1038

662 Messaging Unit .....................................................................................................1038

663

PMON

Unit Base Address Offset. ............................................................................1040

664

PMON

Unit ..........................................................................................................1040

665 PCI Function MMR Locations ...................................................................................1041

666 81341 and 81342 ATUX Configuration Space Base Address Offset................................1042

667 Address Translation Unit Registers — ATUX ..............................................................1043

668 81341 and 81342 ATUE Configuration Space Base Address Offset................................1046

669 Address Translation Unit Registers — ATUE ..............................................................1047

670 Intel

81348 I/O Processor PCI Function Visibility .....................................................1051

671 Coprocessor Registers Assigned to Integrated Peripherals...........................................1052

672 Coprocessor Register Locations...............................................................................1053

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands