Intel 81341 Developer'S Manual Download Page 306

Page: 306 / 1056

Intel

81341 and 81342—Address Translation Unit (PCI Express)

Intel

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

306

Order Number: 315037-002US

3.16.11 ATU Header Type Register - ATUHTR

Header Type Register bit definitions adhere to PCI Local Bus Specification, Revision 2.3.

This register indicates the layout of ATU configuration space bytes 10H to 3FH. The

MSB indicates whether or not the device is multi-function.

Table 144. ATU Header Type Register - ATUHTR

Bit

Default

Description

End Point:

DF_SEL[2:0]

“000”

Root

Complex:

Single Function/Multi-Function Device - Identifies the 81341 and 81342

as a single-function or multi-

function PCI device depending on the setting of the

DF_SEL[2:0]

strap during

P_RST#

assertion.

Note:

The 81341 and 81342 can be configured as a single-function device (ATU only) or a multi-

function device (ATU and storage controller) for split driver support.

As a Root Complex this bit is always ‘0’.

06:00

000000

PCI Header Type - This bit field indicates the type of PCI header implemented. The ATU interface header

conforms to PCI Local Bus Specification, Revision 2.3.

PCI

IOP

Attributes

Attribute Legend:

RV = Reserved

PR = Preserved

RS = Read/Set

RW = Read/Write

RC = Read Clear

RO = Read Only

NA = Not Accessible

Internal Bus Address Offset

+00EH

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands