Intel 81341 Developer'S Manual Download Page 215

Page: 215 / 1056

Intel

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

215

Address Translation Unit (PCI-X)—Intel

81341 and 81342

2.13.71 Outbound Upper Memory Window Base Address Register 0 -

OUMBAR0

The OUMBAR0 register locates Outbound Memory Window 0 in a 4 Gbyte Memory

section in the 81341 and 81342 64 Gbyte internal address space. When A[35:32] of

the internal bus address matches the value in OUMBAR0[3:0], the ATU claims the

transaction and forward it over to the PCI interface.

Note:

In translating the internal bus address A[35:0], A[31:0] is forwarded over to the PCI

bus unmodified. The ATU constructs a 64 bit PCI address in conjunction with the

“Outbound Upper 32-bit Memory Window Translate Value Register 0 - OUMWTVR0” on

page 216

Table 94. Outbound Upper Memory Window Base Address Register 0 - OUMBAR0

Bit

Default

Description

Outbound Window 0 Enable - When set, the ATU Outbound Memory Window 0 claims internal bus

transactions when A[35:32] matches OUMBAR0[3:0].

30:28

000

Outbound Window 0 Function Number Mapping - Errors with Outbound Memory Window 0 transactions

(PCI or Internal Bus) is associated with the function number contained in this field.

Big Endian Byte Swap enable - When set the ATU performs a byte swap on all read/write transactions

through this BAR. When clear, no swap is performed. Refer to

Section 2.3, “Big Endian Byte Swapping”

on page 83

for more details.

26:04

000 0000H Reserved

3:0

Outbound Upper Memory Window Base Address 0 - This value represents bits 35 to 32 of the internal

bus address used to claim an outbound memory request.

Note:

The ATUE has the same default value. When both ATUs exist and the outbound windows of the

both ATUs are enabled, the bit field must be reprogrammed to avoid a conflict.

PCI

IOP

Attributes

Attribute Legend:

RV = Reserved

PR = Preserved

RS = Read/Set

RW = Read/Write

RC = Read Clear

RO = Read Only

NA = Not Accessible

Internal Bus Address

+308H

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands