Intel 81341 Developer'S Manual Download Page 1005

Page: 1005 / 1056

Intel

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

1005

Test Logic Unit and Testability—Intel

81341 and 81342

20.0

Test Logic Unit and Testability

20.1

Overview

This chapter summarizes testability and configuration features incorporated in the

Intel

81341 and 81342 I/O Processors (81341 and 81342).

The test and control logic is based on the IEEE 1149.1-2001 Standard Test Access Port

and Boundary-Scan Architecture document (available from the IEEE). The TAP

controller supports on-chip test logic such as Built-In Self Test and boundary-scan.

«
...
1003
1004
1005
1006
1007
...
»

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands