Intel 81341 Developer'S Manual Download Page 399

Page: 399 / 1056

Intel

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

399

Address Translation Unit (PCI Express)—Intel

81341 and 81342

3.16.117 PCI Interface Error Mask - PIE_MSK

The PCI Interface Error Mask register controls reporting of individual errors by the

device to the Intel XScale

processor core via an interrupt (ATUISR bit 10). A masked

error (respective bit set to 1b in the mask register) is not logged in the Header Log

Table 251. PCI Interface Error Mask - PIE_MSK

Bit

Default

Description

Received Completion with Unsupported Request Mask

Received Completion with Completer Abort Mask

Poisoned TLP Transmitted Mask

Transmit: Header Parity Error Mask

27:21

Reserved Zero - Software must write 0 to these bits.

Unsupported Request Error Status Error Mask - When ‘1’ error reporting is masked.

ECRC Check Error Mask - When ‘1’ error reporting is masked.

Malformed TLP Error Mask - When ‘1’ error reporting is masked.

Receiver Overflow Error Mask - When ‘1’ error reporting is masked.

Unexpected Completion Error Mask - When ‘1’ error reporting is masked.

Completer Abort Error Mask - When ‘1’ error reporting is masked.

Completion Time Out Error Mask - When ‘1’ error reporting is masked.:

Flow Control Protocol Error Status Error Mask - When ‘1’ error reporting is masked.

Poisoned TLP Received Error Mask - When ‘1’ error reporting is masked.

11:5

Preserved.

Data Link Protocol Error Mask - When ‘1’ error reporting is masked.

3:1

Preserved.

Training Error Mask - When ‘1’ error reporting is masked.

PCI

IOP

Attributes

Attribute Legend:

RZ = Reserved Zero

PR = Preserved

RS = Read/Set

RW = Read/Write

RC = Read Clear

RO = Read Only

NA = Not Accessible

Internal Bus Address Offset

+388H

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands