Intel 81341 Developer'S Manual Download Page 878 | Manualshive

Page: 878 / 1056

background image

Intel

®

81341 and 81342—SMBus Interface Unit

Intel

®

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

878

Order Number: 315037-002US

14.4.7

SMBus Controller Data Register — SM_DATA

This register is used to read or write data to the desired Configuration Register.
At the completion of a Read command, this register contains the data from the selected

configuration register. For reads the data register always returns 32 bits and is always

aligned on a DWORD boundary.
Before issuing a write command this register should be written with the desired write

data. For a byte, only the D[7:0] data is written to the desired configuration register.

For a word write, only the D[15:0] data is written to the desired configuration register.

The register number must be word aligned for word writes. For a DWORD write, all 32

bits of data are used. The register number must be DWORD aligned.
The Status Register should be checked to make sure that there is not a command

currently in progress, before writing to this register. Writing to this register when the

Busy bit in the Status Register is asserted, has indeterminate effects.

14.4.8

SMBus Controller Status Register — SM_STS

The SM_STS Register provides the status of the internal transaction. For an SMBus read

transaction, the data is preceded by a byte of status.

Table 557. SMBus Controller Data Register — SM_DATA

Bit

Reset

Description

31:24

00H

Byte 3 (B3): Data bits [31:24].

23:16

00H

Byte 2 (B2): Data bits [23:16].

15:08

00H

Byte 1 (B1): Data bits [15:8].

07:00

00H

Byte 0 (B0): Data bits [7:0].

Table 558. SMBus Controller Status Register — SM_STS

Bit

Reset

Description

07

0

Reserved

06

0

Internal Address Error

05

0

Internal Master Abort

04

000

Internal Target Abort

03:01

0

Reserved

00

000

Successful

Notes:

1.

An Address Error is signalled when an address parity is detected. The error is logged in the System Controller.

«
...
876
877
878
879
880
...
»

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 81341

LS42 - BladeCenter - 7902

Brand: IBM Pages: 56

Brand: IBM Pages: 2

BladeCenter Management Module

Brand: IBM Pages: 78

Brand: IBM Pages: 110

Remote Supervisor Adapter II

Brand: IBM Pages: 132

Brand: Quantum Pages: 20

Brand: TFortis Pages: 86

Brand: Maxim Pages: 26

Brand: T.A Pages: 11

Brand: UNA AUTOMATION Pages: 20

Brand: SIIG Pages: 20

Brand: ADTRAN Pages: 2

Brand: Medel Pages: 28

4 Channel Input Buffer Board SDAIBB

Brand: B&B Electronics Pages: 22

Brand: Avenview Pages: 28

Brand: TRENDnet Pages: 12

Bluespoon 17-1000

Brand: Radio Shack Pages: 1

Brand: Compro Technology Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands