Intel 81341 Developer'S Manual Download Page 177

Page: 177 / 1056

Intel

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

177

Address Translation Unit (PCI-X)—Intel

81341 and 81342

2.13.32 Inbound ATU Translate Value Register 1 - IATVR1

The Inbound ATU Translate Value Register 1 (IATVR1) in conjunction with the

“Inbound

ATU Upper Translate Value Register 1 - IAUTVR1” on page 177

contain bits 35 to 12 of

the internal bus address used to convert PCI bus addresses. The converted address is

driven on the internal bus as a result of the Inbound ATU address translation.

2.13.33 Inbound ATU Upper Translate Value Register 1 - IAUTVR1

The Inbound ATU Upper Translate Value Register 1 (IAUTVR1) in conjunction with the

“Inbound ATU Translate Value Register 1 - IATVR1” on page 177

contain bits 35 to12 of

the internal bus address used to convert PCI bus addresses. The converted address is

driven on the internal bus as a result of the inbound ATU address translation.

Table 55. Inbound ATU Translate Value Register 1 - IATVR1

Bit

Default

Description

31:12

00000H

Inbound ATU Translation Value 1: Bits 31 to 12 of the internal bus address used to convert the PCI

address to internal bus addresses. Must be naturally aligned with the IABAR1 register’s programmed

value (see

Section 2.13.23, “Determining Block Sizes for Base Address Registers” on page 169

11:01

000H

Reserved

Big Endian Byte Swap enable:

0 = No swap performed. See

Section 2.3, “Big Endian Byte Swapping” on page 83

for more details.

1 = Performs a byte swap on all PCI read/write transactions through BAR1.

PCI

IOP

Attributes

Attribute Legend:

RV = Reserved

PR = Preserved

RS = Read/Set

RW = Read/Write

RC = Read Clear

RO = Read Only

NA = Not Accessible

+050H

Table 56. Inbound ATU Upper Translate Value Register 1 - IAUTVR1

Bit

Default

Description

31:04

000 0000H Reserved

3:0

Inbound Upper ATU Translation Value 1 - This value represents bits 35 to 32 of the internal bus address

used to convert the PCI address to internal bus addresses.

PCI

IOP

Attributes

Attribute Legend:

RV = Reserved

PR = Preserved

RS = Read/Set

RW = Read/Write

RC = Read Clear

RO = Read Only

NA = Not Accessible

+054H

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands