Intel 81341 Developer'S Manual Download Page 848

Page: 848 / 1056

Intel

81341 and 81342—Inter-Processor Messaging Unit

Intel

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

848

Order Number: 315037-002US

13.6.22 Send Queue Control Register 2 — SQCR2

The Send Queue Control Register 2 (SQCR2) provides the ability to reset the Send

Queue 2 Put/Get pointers at the request of the other processor. In addition, the size of

Send Queue 2 is configured by the Send Queue 2 Size field of the SQCR2.

Table 529. Send Queue Control Register 2 — SQCR2

Bit

Default

Description

Send Queue 2 Reset (SQ2R)

— Reinitialize Send Queue 2 by returning the Put/Get pointers to their

default values.

Note:

The reinitialization of Send Queue 2 will not take effect until the Send Queue 2 Reset Request

bit (SQ2RR) in the SQCR2 is set by the other processor. The SQ2R and SQ2RR bits in the

SQCR2 will be reinitialized along with the Put/Get Pointers.

Send Queue 2 Reset Request (SQ2RR)

— The other processor is requesting that Send Queue 2 be

reinitialized by returning the Put/Get pointers to their default values.

Note:

The reinitialization of Send Queue 2 will not take effect until the Send Queue 2 Reset bit (SQ2R)

in the SQCR2 is set. The SQ2R and SQ2RR bits in the SQCR2 will be reinitialized along with the

Put/Get Pointers.

29:15

0000H

Reserved

15:00

0000H

Send Queue 2 Size

— Index of the last queue entry in Send Queue 2.

PCI

IOP

Attributes

Attribute Legend:

RV = Reserved

PR = Preserved

RS = Read/Set

RW = Read/Write

RC = Read Clear

RO = Read Only

NA = Not Accessible

Intel XScale

processor internal bus address offset

+0A64H

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands