Intel 81341 Developer'S Manual Download Page 102

Page: 102 / 1056

Intel

81341 and 81342—Address Translation Unit (PCI-X)

Intel

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

102

Order Number: 315037-002US

2.7.3

Uncorrectable Data Errors on the PCI Interface

Two kinds of uncorrectable data errors can occur on the PCI interface: errors as an

initiator and errors as a target.
Errors encountered as an initiator:

— Outbound Read Request

— Outbound Write Request

— Inbound Read Completions

— Inbound Configuration Write Completion Messages

As an initiator, the ATU provides an error response for uncorrectable data errors on

outbound reads, and uncorrectable data errors occurring at the target for outbound

writes. However, there is no error response for uncorrectable data errors on inbound

configuration write completion messages and inbound read completions.
Errors encountered as a target:

— Inbound Read Request (Immediate Data Transfer)

— Inbound Write Request

— Outbound Read Completions

— Outbound Split (I/O or Configuration) Uncorrectable Write Data Error Messages

— Inbound Configuration Write

— Split Completion Messages

As a target, the ATU provides an error response for uncorrectable data errors on

inbound writes, outbound read completions, outbound uncorrectable split write data

error messages, inbound configuration writes, and split completion messages.

However, there is no error response for uncorrectable data errors on inbound reads.

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands