Intel 81341 Developer'S Manual Download Page 123 | Manualshive

Page: 123 / 1056

background image

Intel

®

81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

123

Address Translation Unit (PCI-X)—Intel

®

81341 and 81342

2.7.9.3

Parity Error on the Internal Bus

The 81341 and 81342 provides support for byte-wise parity protection on the internal

bus. The internal bus consists of a 36 bit address bus and 128 bit data bus; both are

protected by byte-wise parity. The internal bus parity protection is provided

independent of the operating mode of the ATUs PCI interface.
When initiating transactions on the internal bus, the ATUs internal bus interface

generates byte-wise parity. As a target the ATU checks byte-wise parity.
As an initiator, for outbound write transactions the ATU will forward bad data parity on

the PCI bus if the ATU detected a parity error on the internal bus interface. And for

outbound read transactions the ATU will forward bad data parity on the internal bus if

the ATU detected a parity error on the PCI interface. Outbound read parity error will be

detected and logged by the internal bus initiator. For outbound read data that has to

flow through the internal bus bridge, the bridge will log the error. Refer to the internal

bus bridge chapter for more details on how the parity error is handled.
As a target, for inbound read transactions the ATU will forward bad data parity on the

PCI bus if the ATU detected a parity error on the internal bus interface. And for inbound

write transactions the ATU will forward bad data parity on the internal bus if the ATU

detected a parity error on the PCI interface. Inbound write parity error will be detected

and logged by the internal bus target. For write data that has to flow through the

internal bus bridge, the bridge will log the error. Refer to the internal bus bridge

chapter for more details on how the parity error is handled.

2.7.9.3.1 Conventional Mode

On an inbound read transaction, when the data word where the internal bus parity

error is detected is actually requested and returned to the PCI bus, a target abort is

returned to the PCI initiator on that data word. The IRQ is flushed after the completion

cycle is performed on the PCI bus
The following additional actions with the given constraints are performed by the ATU

when a target abort is signaled by the PCI target interface during an inbound read

transaction:

• Set the Target Abort (target) bit (bit 11) in the ATUSR.

• When the ATU PCI Target Abort (target) Interrupt Mask bit in the ATUIMR is clear,

set the PCI Target Abort (target) bit in the ATUISR. When set, no action.

2.7.9.3.2 PCI-X Mode

An internal bus parity error of an inbound read transaction (split read request) on the

Internal Bus results in the following actions.

• The ATU initiates a Split Completion Error Message (with message class=2h -

completer error and message index=81h - 81341 and 81342 internal bus target

abort) on the PCI bus.

• When the Initiated Split Completion Error Message Interrupt Mask in the ATUIMR is

clear, set the Initiated Split Completion Error Message bit in the ATUISR. When set,

no action.

Note:

This split completion error message includes a device specific message index. The error

handler would need to have knowledge of the device specific error messages of the

81341 and 81342 in order to fully diagnose the problem.

«
...
121
122
123
124
125
...
»

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 81341

Brand: Commell Pages: 58

Brand: Blackrock Microsystems Pages: 27

Brand: Barco Pages: 30

Brand: Advantech Pages: 36

Brand: Medel Pages: 28

Brand: Freescale Semiconductor Pages: 8

NVRx-7300 series

Brand: Swann Pages: 9

OMB-DAQBOARD-500 Series

Brand: Omega Pages: 48

Brand: Idis Pages: 22

Brand: ADTRAN Pages: 20

Brand: ZALMAN Pages: 20

Brand: LaView Pages: 2

Brand: JETWAY Pages: 63

Brand: DTS Pages: 94

Diamond Systems DS-MPE-CAN2L

Brand: Fortec Star Pages: 36

3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card...

Brand: 3Com Pages: 6

BS2000 SE Series

Brand: Fujitsu Pages: 43

BS2000 SE Series

Brand: Fujitsu Pages: 93

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands