manualshive.com logo in svg

Intel 81341, Developer'S Manual

The Intel 81341 Developer's Manual is a comprehensive guide to understanding and utilizing the capabilities of this powerful product. Available for free download on our website, this manual provides detailed instructions and information to help developers maximize the potential of the Intel 81341. Download it from manualshive.com.

Share
Download
background image

Intel

®

 81341 and 81342—Clocking and Reset

Intel

®

 81341 and 81342 I/O Processors

Developer’s Manual

December 2007

1000

Order Number: 315037-002US

19.3

Reset Pins

Table 632. Reset Pin Summary

Pin

Input/Output

Description

P_RST#

Input

Primary chip reset. Should be connected to PCI RST# 

or PCI Express PERST# depending on the mode of 

operation.

WARM_RST#

Input

Warm Reset is the same as a cold reset, except sticky 

configuration bits are not reset. This pin should only 

be used when the sticky bit functionality is required. 

In this scenario, the WARM_RST# pin must be tied to 

the system reset PCI_RST# signal while the P_RST# 

pin can be tied to the system power good signal. When 

the sticky bit functionality is not required, the 

WARM_RST# pin should not be used and must be tied 

to Vcc. When the PCI Express interface is used as an 

endpoint, the PCI Express inband Hot Reset 

Mechanism can also be used to provide the sticky bit 

functionality.

Note:

Driving WARM_RST# using any other 

methods than suggested above may result in 

unpredictable behavior of the device.

P_RSTOUT#

Output

Secondary Reset. This is used as the PCI bus reset 

when operating as the Central Resource

PB_RSTOUT#

Output

Peripheral Bus Reset: This signal is asserted whenever 

the internal logic is reset.

PCI Express Hot Reset

n/a

This is an inband reset message that can be received 

as an endpoint, and generated as a root complex. 

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 81341

Laurell WS-650 lite Series Operation Manual preview
WS-650 lite Series
Brand: Laurell Pages: 84
ETAS FETK-S2.1 User Manual preview
FETK-S2.1
Brand: ETAS Pages: 69
Accusys ACS-76500 Owner'S Manual preview
ACS-76500
Brand: Accusys Pages: 34
National Instruments NI-9252 Calibration Procedure preview
NI-9252
Brand: National Instruments Pages: 9
Behringer EXPANSION CARD X-DANTE Quick Start Manual preview
EXPANSION CARD X-DANTE
Brand: Behringer Pages: 65
Nvidia DGX A100 User Manual preview
DGX A100
Brand: Nvidia Pages: 115
ATEN Slideaway CL1008 User Manual preview
Slideaway CL1008
Brand: ATEN Pages: 77
Doremi MB-4K User Manual preview
MB-4K
Brand: Doremi Pages: 15
Icy Box IB-NAS5520 Quick Start Manual preview
IB-NAS5520
Brand: Icy Box Pages: 2
Acromag ACPS3320 User Manual preview
ACPS3320
Brand: Acromag Pages: 35
CAME 848EA-0120 Setup And User'S Manual preview
848EA-0120
Brand: CAME Pages: 32
ADTRAN 1202052L1 User Manual preview
1202052L1
Brand: ADTRAN Pages: 136
SIIG US2273 Quick Installation Manual preview
US2273
Brand: SIIG Pages: 8
M86 Security Web Filter HL User Manual preview
Web Filter HL
Brand: M86 Security Pages: 512
Dahua DHI-NVR5208-4KS2 User Manual preview
DHI-NVR5208-4KS2
Brand: Dahua Pages: 361
Dahua NVR5208-EI User Manual preview
NVR5208-EI
Brand: Dahua Pages: 489
MSE PSE-608R User Manual preview
PSE-608R
Brand: MSE Pages: 35
Dell PowerEdge 2650 Service Manual preview
PowerEdge 2650
Brand: Dell Pages: 65

Brands by name

Popular brands

Load more brands