Intel 81341 Developer'S Manual Download Page 1022

Page: 1022 / 1056

Intel

81341 and 81342—Peripheral Registers

Intel

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

1022

Order Number: 315037-002US

21.6

Peripheral Memory-Mapped Register Address Space

The PMMR address space is divided to support the integrated peripherals on the 81341

and 81342.

Table 638

shows all of the 81341 and 81342 integrated peripheral memory-

mapped registers and their internal bus address offsets. The starting address of the

memory-mapped registers is programmable using the PMMRBAR register. The

PMMRBAR register is located at a fixed location which is at F_FFFF_FFFCH. The default

starting address of the PMMR register block is at 0_FFD8_0000H. Software can

reprogram the PMMRBAR register to relocate the memory-mapped register block when

desired. Bits [31:15] of the PMMRBAR register represent bits [35:19] of the 36-bit base

address. The PMMR register block is aligned on a 512 KByte boundary. Bits [14:0] of

the PMMRBAR registers are reserved bits.

Table 638

lists the peripherals and the relative address offsets from the PMMRBAR

content.

Warning:

Care must be exercised when updating memory-mapped registers, because some of

the registers can have side-effects on other registers and resources in the 81341 and

81342 architecture. As an example, updating a Base Address Register (such as the

PMMRBAR) relocates other registers and resources in the 81341 and 81342

architecture, and software must not access these related registers and resources until

software can ensure that the Base Address Register has truly been updated. Refer to

the Intel XScale

Microarchitecture Developer’s Manual, which describes various

methods of fencing memory accesses.

Table 637. PMMR Base Address Register (PMMRBAR) Default Value

Absolute Address

PMMRBAR

F_FFFF_FFFCH

Table 638. Local Addresses for Integrated Peripherals (Sheet 1 of 3)

Integrated Peripheral

Internal Address Offset

(Relative to PMMRBAR)

Space

Allocated

“Application DMA Unit”

+0000H through 01FFH

512 Bytes

“Application DMA Unit”

+0200H through 03FFH

512 Bytes

“Application DMA Unit”

+0400H through 05FFH

512 Bytes

Reserved.

+0600H through 07FFH

512 Bytes

Not Claimed by any Unit

+0800H through 09FFH

“Inter-Processor Messaging Unit”

+0A00H through 0CFFH

768 Bytes

Not Claimed by any Unit

+0D00H through 14FFH

“SRAM Memory Controller”

+1500H through 157FH

128 Bytes

“Peripheral Bus Interface Unit”

+1580H through 15FFH

128 Bytes

Not Claimed by any Unit

+1600H through 163FH

“System Controller Unit”

+1640H through 164FH

16 Bytes

Not Claimed by any Unit

+1650H through 167FH

32 Bytes

Not Claimed by any Unit

+1680H through 16FFH

Not Claimed by any Unit

+1700H through 177FH

“Internal Bus Bridge”

+1780H through 1797H

24 Bytes

Not Claimed by any Unit

+1798H through 177FH

104 Bytes

“DDR SDRAM Memory Controller”

+1800H through 19FFH

512 Bytes

Not Claimed by any Unit

+1A00H through 1FFFH

“I/O Pad Control Unit”

+2000H through 21FFH

512 Bytes

Reserved

+2200H through 221FH

32 Bytes

«
...
1020
1021
1022
1023
1024
...
»

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands