Intel 81341 Developer'S Manual Download Page 470

Page: 470 / 1056

Intel

81341 and 81342—Application DMA Unit

Intel

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

470

Order Number: 315037-002US

Each word in the chain descriptor is analogous to control register values. Bit definitions

for the words in the chain descriptor are the same as for the control registers.

• The first eight words are the Basic descriptor. Please see

Section 5.3.1, “Basic

Chain Descriptor Format” on page 467

for more details.

• The ninth word is the lower 32-bit source address for source 1 of the XOR-transfer

operation. This value is loaded into the Source Lower Address Register 1.

• The tenth word is the upper 32-bit source address for source 1of the XOR-transfer

operation. This value is loaded into the Source Upper Address Register 1.

• The eleventh word is the lower 32-bit source address for source 2 of the XOR-

transfer operation. This value is loaded into the Source Lower Address Register 2.

• The twelfth word is the upper 32-bit source address for source 2 of the XOR-

transfer operation. This value is loaded into the Source Upper Address Register 2.

• The thirteenth word is the lower 32-bit source address for source 3 of the XOR-

transfer operation. This value is loaded into the Source Lower Address Register 3.

• The fourteenth word is the upper 32-bit source address for source 3 of the XOR-

transfer operation. This value is loaded into the Source Upper Address Register 3.

• The fifteenth word is the lower 32-bit source address for source 4 of the XOR-

transfer operation. This value is loaded into the Source Lower Address Register 4.

• The sixteenth word is the upper 32-bit source address for source 4 of the XOR-

transfer operation. This value is loaded into the Source Upper Address Register 4.

• The seventeenth word is the lower 32-bit source address for source 5 of the XOR-

transfer operation. This value is loaded into the Source Lower Address Register 5.

• The eighteenth word is the upper 32-bit source address for source 5 of the XOR-

transfer operation. This value is loaded into the Source Upper Address Register 5.

• The nineteenth word is the lower 32-bit source address for source 6 of the XOR-

transfer operation. This value is loaded into the Source Lower Address Register 6.

• The twentieth word is the upper 32-bit source address for source 6 of the XOR-

transfer operation. This value is loaded into the Source Upper Address Register 6.

• The twenty first word is the lower 32-bit source address for source 7 of the XOR-

transfer operation. This value is loaded into the Source Lower Address Register 7.

• The twenty second word is the upper 32-bit source address for source 7 of the

XOR-transfer operation. This value is loaded into the Source Upper Address

• The twenty third word is the lower 32-bit source address for source 8 of the XOR-

transfer operation. This value is loaded into the Source Lower Address Register 8.

• The twenty fourth word is the upper 32-bit source address for source 8 of the XOR-

transfer operation. This value is loaded into the Source Upper Address Register 8.

• The twenty fifth word is the lower 32-bit source address for source 9 of the XOR-

transfer operation. This value is loaded into the Source Lower Address Register 9.

• The twenty sixth word is the upper 32-bit source address for source 9 of the XOR-

transfer operation. This value is loaded into the Source Upper Address Register 9.

• The twenty seventh word is the lower 32-bit source address for source 10 of the

XOR-transfer operation. This value is loaded into the Source Lower Address

• The twenty eighth word is the upper 32-bit source address for source 10 of the

XOR-transfer operation. This value is loaded into the Source Upper Address

• The twenty ninth word is the lower 32-bit source address for source 11 of the XOR-

transfer operation. This value is loaded into the Source Lower Address Register 11.

Summary of Contents for 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands

Intel 81341, Developer'S Manual

Search results

Summary of Contents for 81341

Reviews:

Related manuals for 81341

Brands by name

Popular brands