GRAUPNER mx-24s, Programming Manual

Page: 116 / 216

116 116 Program description: Mixers
Model type: “2 AIL 1 / 2 / 4 FL”
If you enter “2 AIL 1 FL” in the “Ailerons / fl aps”
line of the »
Model type « menu (see page 70), the
transmitter’s “Wing mixer menu” will look similar to the
screen-shot printed below:
0% 0%
0%
0%
Multi-flap menu
Brake settings
Aileron
Flaps
=>
=>
2–>4 rudder
6–>3 elevator
Aileron differential
W I N G M I X E R S
If you enter “2 AIL 2 FL” or “2 AIL 4 FL” in the “Ai-
lerons / fl aps” line of the »
Model type « menu (see
page 70), the transmitter’s “Wing mixer menu” will
look similar to the screen-shot below:
Multi-flap menu
Brake settings
Aileron
Flaps
«Normal »
=>
=>
2–>4 rudder 0%
6–>3 elevator 0% 0%
W I N G M I X E R S
All the available parameters can be adjusted separa-
tely for each fl ight phase, regardless of the combinati-
on of aileron and fl ap servos you have selected.
Tip:
We recommend that you make use of the Servo Dis-
play facility, where you can check the results of your
settings. This is available from virtually any menu po-
sition by pressing the
HELP button with the rotary
control pressed in.
Before we address the details of this menu we would
like to provide a brief explanation of the different ap-
pearances of the multi-fl ap menu:
Model type: “2 AIL 1 FL”
If you have connected the servos to the receiver in
the order described in the section starting on page
37, and have selected them as shown in the »
Model
type « menu (see page 70), then the abbreviations
“AIL” and “FL” refer to the wing fl aps as shown below:
AIL
left FL FL AIL
right
Since the options available in the wing mixer menu
and its sub-menus vary according to the number of
fl ap servos which you have entered in the »
Model
type « menu (see page 70), the list only contains tho-
se set-up options which are possible for your model
confi guration.
For this reason, if you have pre-selected “2 AIL 1 FL”,
both the options for superimposing the aileron func-
tion on the fl aps are suppressed, as are all the set-up
options in the (right-hand) column “FL2”.
Fl.pos
0% 0%
FL 0% 0% +100% +100%
El–>Fl 0% 0% 0% 0%
AILE
SEL SEL
FLAP
A further difference is that the settings for “Aileron dif-
ferential” are not found in the “multi-fl ap menu”, as
with “2 AIL 2/4 FL”, but one level higher in the »
Wing
mixers « menu – see the screen-shot at top left.
Model type: “2 AIL 2 FL”
If you have connected the servos to the receiver in
the order described in the section starting on page
37, and have selected them as shown in the »
Model
type « menu (see page 70), then the abbreviations
“AIL” and “FL” refer to the wing fl aps as shown below:
AIL
left
FL FL
right
AIL
Since the options available in the wing mixer menu
and its sub-menus vary according to the number of
fl ap servos which you have entered in the »
Model
type « menu (see page 70), the list only contains tho-
se set-up options which are possible for your model
confi guration.
For this reason, if you have pre-selected “2 AIL 2 FL”,
all the set-up options for the second pair of fl aps are
suppressed in the (right-hand) column “FL2”.
AI +100% 0%
Ail–tr 0%
Diff. 0% 0%
Fl.pos 0% 0%
FL 0% 0% +100% +100%
El–>Fl 0% 0% 0% 0%
AILE
SEL SEL
+100%
FLAP