Panasonic S-3650PF3E Скачать руководство пользователя страница 231

Страница: 231 / 321

5-2-1-2

Check Prior to Auto Address Setting

Connect the wiring

correctly

* If an outdoor unit displays an alarm, conduct this process after diagnosing the problem.

Has the wiring of the indoor/outdoor been completed?

Is it all connected correctly?

Run the auto address setting.

1-1

Run the auto address setting.

Is the power of the indoor unit(s) and outdoor unit(s) on?

2-1

Be sure that the indoor and outdoor units are connected with

correct combination described in the catalog.

3-4

3-1

Be sure that the detailed setting items are made at factory setting.

Be sure that the indoor and outdoor units are connected

with correct combination written in catalog.

3-3
3-4

3-2 Is the remote control wiring connected with two indoor/outdoor

combinations or more for group control?

Turn on the power of only one system and run auto address setting again. Upon completion of

the auto address setting, turn on the power for the next system and run auto address setting

while still power switched on, units whose auto address setting have completed. (In the case

of multiple systems, run the auto address setting respectively in due order for each system.)

3-3

Power on

2-1

3-1

Correct the connection

Yes

3-2

Yes

Correct the connection

4-2

Yes

4-3

Yes

No Correct the setting

Installation

[ U3, F3 ]

Relocation

and resetting

of address

or setting

Indoor/

outdoor

wiring

Address

1 Auto

Factory setting
Item code

Item

Value

99
99
99

Indoor unit capacity

Indoor unit address
Group conrol address

System address

12
13
14

For information on the remote control’s detailed settings, refer to the Reference Materials.

4-1

4-2

4-3

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 2

2020/01/29 21:17:40

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды