manualshive.com logo in svg

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Panasonic S-3650PF3E - Мощный и надежный продукт с выдающимися характеристиками. Теперь вы можете с легкостью узнать больше о его технических данных и обслуживании, скачав бесплатный руководство по эксплуатации с manualshive.com. Не упустите шанс загрузить его и улучшить свой пользовательский опыт.

Поделиться
Скачать
background image

4-20

4

5

1

E

6

1

E

0

2

E

Check items

Check that the indoor unit power is turned ON.
Check that the inter-unit control wiring is connected correctly. (Check that there are no open 

circuits, short circuits, terminal plugs, incorrect wiring to the remote controller terminals, or 

similar problems.)

Check that the remote controller wiring is connected correctly. (Check that there are no open 

circuits, short circuits, incorrect wiring to the inter-unit control wiring terminals, control wiring 

for group control, or similar problems.)

Check that there are no indoor units where the item code 11, 12, 13, 14 was already 

[ U3, F3 ]

incorrectly set by manual or auto address setting.

•

•

•

•

If one of the below alarms appears when the remote controller is operated after auto address setting was 

completed.

Cause

E01

E02

P09

Remote controller

display

Nothing is 

displayed.

The remote controller is not connected correctly (remote controller receiving trouble).

The remote controller of an indoor unit where the indoor unit address is not set is inadvertently 

operated. (Communications with the outdoor unit are not possible.)
The remote controller is not connected correctly (trouble with sending of the signal from the 

remote controller to the indoor unit).
The indoor unit ceiling panel connector is not connected correctly.

Even if alarm E15 or E16 appears, addresses are set at those indoor units which could be verified. The set

addresses can be checked using the remote controller.

In the case of indoor unit group control, if there is a mistake in the remote controller inter-unit control wiring for 

group control, addresses may not be set even if                (SETTING) appears.

When auto address setting is started from the remote controller, 

,

                (SETTING) appears on the remote 

controller at units where the inter-unit control wiring and remote controller wiring are connected correctly. 

The remote controller is not connected correctly (power trouble).

The indoor unit power was cut off after auto address setting was completed.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb   20

2020/01/30   13:58:50

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

TCF T Series Instruction, Operation And Maintenance Manual preview
T Series
Бренд: TCF Страницы: 19
Haier T-Series Service Manual preview
T-Series
Бренд: Haier Страницы: 56
Samsung AC TN4F Series User Manual preview
AC TN4F Series
Бренд: Samsung Страницы: 22
TATA Motors TSR Series Installation, Use And Manteinance Manual preview
TSR Series
Бренд: TATA Motors Страницы: 32
Mars A-DVH09SF-0 Installation Manual preview
A-DVH09SF-0
Бренд: Mars Страницы: 36
Airwell AW-YSDM048-H11 Installation Manual preview
AW-YSDM048-H11
Бренд: Airwell Страницы: 20
Daikin RXS-L Technical Data Manual preview
RXS-L
Бренд: Daikin Страницы: 65
Zibro P 629 Operating Manual preview
P 629
Бренд: Zibro Страницы: 18
Timberk T-AC07-S25-X Instruction Manual preview
T-AC07-S25-X
Бренд: Timberk Страницы: 56
Walter Roller FHVI/T Series Mounting Instructions preview
FHVI/T Series
Бренд: Walter Roller Страницы: 36
Turbo Air TAS-18MVHN/O Installation Manaul preview
TAS-18MVHN/O
Бренд: Turbo Air Страницы: 33
Prem-I-Air EH1614/EU Manual preview
EH1614/EU
Бренд: Prem-I-Air Страницы: 15
Carrier 50PG08 14 Series Installation Instructions Manual preview
50PG08 14 Series
Бренд: Carrier Страницы: 20
Daikin SkyAir RZQ-P Series Engineering Data preview
SkyAir RZQ-P Series
Бренд: Daikin Страницы: 238
ProKlima 28188421 Manual preview
28188421
Бренд: ProKlima Страницы: 148
White Rodgers ACB1000 Owner'S Manual preview
ACB1000
Бренд: White Rodgers Страницы: 8
Blueridge BMKH09M-LM Owner'S Manual preview
BMKH09M-LM
Бренд: Blueridge Страницы: 28
Friedrich ZoneAire Compact P08SA Owner'S Manual preview
ZoneAire Compact P08SA
Бренд: Friedrich Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды