Panasonic S-3650PF3E Скачать руководство пользователя страница 89

Страница: 89 / 321

1-11-1-1-13

(5) How to Attach the Corner & Air Intake Grille

A. Attaching the corner cover

Check that the safety strap from the corner cover is

fastened to the panel for cassette pin, as shown in the figure.

)

panel for cassette.

(4) Wiring the Panel for Cassette

)

the indoor unit control PCB.

Connect the 22P connector (white) from the panel for

cassette to the connector on the indoor unit control

PCB in the unit electrical component box. In this case,

expose the cutout section of the tube for the wiring

protection to the outside from the electrical component

box and fix it with the clamper attached to the electrical

component box.

)

Insert connector lock facing PCB edge until it is

locked in place. (If not connected completely, the

Auto Flap will not operate and “P09” is displayed on

the remote controller. When the connector plugged

in the wrong direction, parts on the PCB may be

damaged.)
Check that the wiring connector is not caught

between the electrical component box and the

cover.

Check that the wiring connector is not caught

between the unit and the panel for cassette.

B. Attaching the air intake grille

To install the air intake grille, follow the steps for

“Removing the grille” in the reverse order. By rotating the

air intake grille, it is possible to attach the grille onto the

panel for cassette from any of 4 directions. Coordinate the

directions of the air intake grilles when installing multiple

units, and change the directions according to customer’s

requests.

When attaching the air intake grille, be careful that the

flap lead wire does not become caught.

Be sure to attach the safety strap that prevents the air

intake grille from dropping off to the panel for cassette

unit as shown in the figure below.

With this panel for cassette, the directions of the air

intake grille lattices when installing multiple units, and the

position of the label showing the company name on the

corner panel, can be changed according to customer’s

requests, as shown in the figure below. However, the

wireless signal receiver can only be installed at the

refrigerant-tubing corner of the ceiling unit.

Hole of panel for cassette hook

Can be installed

rotated 90°

Hook that prevents the grille from dropping

Supplied screw

Place the corner cover

so that the 5 tabs fit into

the holes in the panel

for cassette. Then

fasten it in place with

the supplied screws.

Lid of electrical component box

Cutout section of the tube

for wiring protection

Panel for

cassette wiring

connector

Connector

Lock

22P (white)

Screws (×2)

Wiring diagram

(Direction that the unit faces

has been changed to facilitate

explanation.)

Optional wireless receiver kit

for installation.

* This position is only possible

Corner cover installation

position marked with the

Panasonic Logo at shipment.

of 4 corners

Electrical component

box

Locations of air intake grille

hinges at shipment

* The grille can be installed with

these hinges facing in any of 4

directions.

Refrigerant tube side

Drain pipe side

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 13

20/01/30 10:25:11

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды