Panasonic S-3650PF3E Скачать руководство пользователя страница 113

Страница: 113 / 321

1-11-1-1-37

85464369939000

Printed in JAPAN

PA0816-0

CV6233336305

Applicable indoor units:4-Way Cassette

●

Before proceeding with the installation work, please read carefully through the installation instructions which are provided with the

ceiling panel and the indoor unit and also through the installation instructions which you are now reading. In particular, be absolutely

sure to read through the “Safety Precautions” prior to installation. Also ensure that the user keeps these installation instructions

in a safe place for future reference.

■

The actions which must or must not be taken are described using the following pictographs.

■

The

stallat

ion wo

hould b

ste

the

ealer

the

ere

the

uni

rchase

d o

liz

tract

the

uni

stalle

rrectly

ing onl

the

d p

arts

hou

(Failure to follow this instruction may cause the unit to fall down, water to leak, electric shocks and/or a fire.)

■

ing onl

the

ign

ate

the

ing

onn

ecte

rrectly,

sec

d in

that

the

exter

force of the cables will not be

transmitted to the terminal connections.

(Failure to follow this instruction may cause trouble, heat to be generated and/or a fire.)

■

Ret

the

vers

erly

the

igin

l po

ion

whil

ing

that

non

the

res

pin

che

d o

tra

(Failure to follow this instruction may cause electric shocks and/or a fire.)

■

The

uni

stalle

rrectly

cat

ion whi

h i

str

ong

nough

o b

ear

the

igh

the

arts.

(Failure to follow this instruction may result in injuries caused by the unit falling down.)

■

The

arts

d b

oni

the

access

arts.

(Failure to use the specified parts may cause the unit to fall down and/or water to leak.)

■ The kit must not be installed in a location where flammable gases may

leak in the area around it.

(Failure to follow this instruction may cause ignition if gas should leak and accumulate in the area around the unit.)

These precautions describe instructions which must be followed in order to avoid personal injuries and/or property damage.

■

They describe the instructions using categories which are classified by the extent of the injuries and/or damage caused by incorrect

or improper acts.

These precautions must be observed without fail.

This indicates an action which must be taken

(that is, an action which is mandatory).

CAUTION

This symbol refers to a hazard or

unsafe practice which can result in

personal injury or product or property

damage.

WARNING

This symbol refers to a hazard or

unsafe practice which can result in

severe personal injury or death.

WARNING

This indicates an action which must not

be taken (that is, an action which is prohibited).

■ Do not connect any of the wires from a midway point.

(Failure to follow this instruction may cause defective contact, defective insulation or a current whose level exceeds

what is permissible, resulting in electric shocks and/or a fire.)

■ Do not stow any power cables which have been bundled together using a

tie or other means.

(Failure to follow this instruction may cause heat to be generated and/or a fire.)

Safety Precautions

INSTALLATION INSTRUCTIONS

Air intake chamber

Model No.CZ-FDU3

Select

ing

It is necessary to set the fan speed in accordance with the intended application and the optional parts to be

used if any such part is used. (Table 1-11-1-1-1)

If this speed is not changed, a reduction in the air flow may result, causing the air outlet temperature to drop

and condensation to form during cooling.

There are two ways to set the fan speed: either (1) change the positions of the DIP switches on the indoor unit

control PCB or (2) set the speed using the wired remote controller. Select one of these ways.

* Priority is given to setting the fan speed by changing the positions of the DIP switches.

Indoor unit control PCB

Intended application /

name of optional parts

Setting

(1)

Item code

5D/5d

setting data

0001

0000

DC fan motor tap setting table

Standard (factory setting)

High-ceiling setting 1

(with standard, ECONAVI panel)

Air-flow blocking kit

(when a duct is connected.)

Intended application /

name of optional parts

Setting

Item code

5D/5d

setting data

(3)

(6)

0003

0006

Air-flow blocking kit (for 3-way air flow)

High-ceiling setting 2

(with standard, ECONAVI panel)

Air-flow blocking kit

(for 2-way air flow)

<Procedure> Be absolutely sure to turn off the

power (earth-leakage circuit breaker).

<1> On Table 1-11-1-1-1, check out the “Setting No.”

that corresponds to the intended application

and the optional parts to be used.

<2> Open the cover of the electrical component box,

and check the indoor unit control PCB.

(Fig. 1-11-1-1-3)

<3> Select the Setting No. which was checked out

on Table 1-11-1-1-1, and change the positions of

the DIP switches on the indoor unit control PCB.

(1) When setting the fan speed by changing

the positions of the DIP switches on the

indoor unit control PCB

(2) When setting the fan speed using a wired remote controller

(optional parts: CZ-RTC5A, CZ-RTC5B

)

“OFF” position

1 2 3

TP6

TP3

TP1

2 3

DIP switch

Setting

No.

“OFF” position

“ON” position

DIP switch

“OFF” position

“ON” position

TP6

TP3

TP1

2 3

DIP switch

“ON” position

TP6

TP3

TP1

(3)

(6)

(1)

On Table 1-11-1-1-1, check out the “Item code 5D setting data” that corresponds to the

intended application and the optional parts to be used.

(3) When setting the fan speed using a wired remote controller

(optional parts: CZ-RTC4)

On Table 1-11-1-1-1, check out the “Item code 5d setting data” that corresponds to the

intended application and the optional parts to be used.

<1> Hold down the + + buttons together for at least 4 seconds.

The maintenance function screen is displayed.

<2> Use the / buttons to select the display and the / buttons to

select the page.

Select “8.Detailed settings” and press the button.

The [Detailed settings screen] appears.

Using the / buttons, select the unit No.

<3> Using the / buttons, select the item code.

Using the / buttons, change the item code to “5D.”

<4> Using the / buttons, select the setting data.

Using the buttons, change the setting data to the value checked out

on Table 1-11-1-1-1, and press the button.

<5> After selecting the unit No. using the / buttons, press the button.

The [Detailed settings completion screen] appears.

Select “Yes” , and press the .

<1> Hold down the + + buttons together for at least 4 seconds.

<2> Each time the button is pressed, the numbers of the indoor units under group

control are displayed in sequence.

The fan motor of only the indoor unit that has been selected will run.

<3> Specify item code “5d” using the temperature setting / buttons.

<4> Change the setting data using the hour buttons. The setting data details

are as given on Table 1-11-1-1-1.

<5> Press the button. (OK if the display changes from flashing to lighted.)

<6> Press the button. The normal stop status is established.

Go to step <2> to change the selected indoor unit.

<7> Press the button. The normal stop status is established.

(1)

0001

Detailed settings

Unit no.

Code no.

Set data

0001

1-1

20:30 (THU)

Sel.

Unit No.

Setting data

Item code

Detailed settings

Unit no.

Code no.

Set data

0001

1-1

Sel.

20:30 (THU)

Maintenance func

Sel.

20:30 (THU)

Page [

] Confirm

5. Sensor info.

6. Servicing check

7. Simple settings

8. Detailed settings

<Procedure> Ensure that the units have stopped operating before changing the fan speed.

<Procedure> Ensure that the unit has stopped operating before changing the fan speed.

■

Panasonic disclaims all liability for any accidents or damages occurring as a result of installing the kit using any procedures which

are not described in the installation instructions or which do not use the specified parts.Any malfunctioning or trouble caused

by the manner in which the kit was installed will not be covered by the terms and conditions of the product warranty.

■

Usage precautions

• Install this Air intake chamber on the indoor unit before proceeding to install the indoor unit itself.

• During installation, handle this Air intake chamber very carefully since subjecting its sides to impacts may result in damage.

• Keep these installation instructions in a safe place together with the operating instructions of the indoor unit

NOTES

CAUTION

Table 1-1

-1-1-

Fig. 1-11-1-1-3

TP6

TP3

TP1

2 3

TP6

TP3

TP1

1 2 3

SW001

Setting example

1: OFF

2: OFF

3: ON

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 37

20/01/30 10:25:25

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды