Panasonic S-3650PF3E Скачать руководство пользователя страница 55

Страница: 55 / 321

1-7-5

Operating the Timer Remote Controller (CZ-RTC4)

Setting Item Code “ ”

1. Press and hold down the

and

2. The indoor unit numbers in the group control will be

sequentially displayed whenever the Unit Select button is

buttons

(

, the unit no., item code and detailed data will blink

pressed

Only the fan motor for the selected indoor unit will operate

during this time.

3. Specify the “

” item code by pressing the

buttons for the temperature setting buttons and confirm

the values. (“

” set at shipment)

4. Press the

buttons for the time to amend the

”.

6. Press the

values for the set data.

See Table 1-7-3 and Fig. 1-7-2 and select a value

between “

” and “

Select “

” if the auto airflow volume setting is

activated.
Press the

button.

The display will stop blinking and remain illuminated.

button. The fan motor will stop operating

Table 1-7-3 Setting the external static pressure

and the LCD display will return to the normal stop mode.

Indoor unit type

Item code

3650

6071

Outdoor unit type

–

150

External static pressure of the rated

airﬂ

ow volume (Pa)

140
130
120
110

90
70
50
30 *
10

No auto airﬂ

ow volume setting

uto airﬂ

ow volume setting

* Setting at shipment

simultaneously for 4 or more seconds.

on the LCD display.)

1, 6

Failure to set this parameter may result in decreased

airﬂ

ow and condensation.

Auto Airflow Volume Control Operations and External

Static Pressure Setting-Check Operation

1. Press and hold down the

button for 4 or more seconds.

“

” will be displayed on the LCD display.

2. Press the

button to start the test run.

pressing the

(Fan) by

(Mode select) button.

ing the

by press-

(Fan speed) button.

NOTE

and external static

4. The fan motor will be activated and auto airflow volume

control operations or external static pressure setting-check

5. Press the

button to halt the test run.

operations will be started.

The power of the airflow will change while these operations

are in progress.

The external static pressure setting-check operations and

auto airflow volume control operations will be completed in

about 3 to 30 minutes.
“

” display will be disappeared from the LCD display.

2, 5

pressure setting-check operations will not be performed

unless the above settings are made.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 5

20/01/30 10:24:49

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды