Panasonic S-3650PF3E Скачать руководство пользователя страница 236

Страница: 236 / 321

5-2-1-7

Power on
2-1

Is the indoor unit powered off?

Is/was the power to the outdoor unit cut off?

1-1

1-2

Disconnect the connector mentioned above on the control PC board

of the indoor unit control PC board, and see whether the E04 goes off

after several minutes. (When doing so, if two remote controllers are

being used and the wireless remote controller is the main remote

controller, set the other remote controller as the main.)
Replace wireless remote control parts including wiring.

4-3

4-4

Is the LED on the indoor unit control PC board blinking?

4-5

Are all the remote controllers of the other indoor

units connected to that outdoor unit displaying E04?

4-7

The nonvolatile memory (EEPROM) on the indoor unit’s control PC board is either not installed,

improperly installed or the nonvolatile memory is faulty. Correct this or after replacing the

nonvolatile memory, write model data to it in the remote control detailed settings mode.

4-6

Are the CHK pin and/or TEST pin on the indoor unit control PC

board short-circuited?

4-1

Is the wireless remote controller connected to on the indoor unit’s

control PC board?

4-2

Is the indoor/outdoor wiring connected correctly?

2-1

3-2
3-3

Was the number of indoor units increased or decreased after

auto address setting was complete?

3-1

Conduct checks prior to auto address setting.

3-2

After turning the power

on, wait three minutes

1-2

3-1
Correct the wiring

Yes

4-4

4-5

Yes

Remove the short
4-2

Yes

4-3
4-5

Yes

No 4-1

Check the indoor unit addresses from the remote control’s

detailed settings mode.

Is it Not Set (99), or is the indoor unit’s address duplicated?

3-3

Indoor/

outdoor

wiring

4 Indoor

unit

control

PC board

3 No. of

Indoor

Units

1 Power

Source

E04 Error in Indoor Unit Receiving Signal from the Outdoor unit

Error Detection Method

Error Diagnosis

When there is no communication within a 3-minute period from the outdoor unit. Or, judged an error when no reply comes

from the outdoor unit.

The outdoor unit is not turned on.

When the network of indoor/outdoor operation line was wired, the (SHORT) setting of the terminal resistor switch on the

outdoor control PC board was set on multiple units (four or more).

When the power was turned on after auto address setting was completed, the number of indoor units had been changed.

Forgot to turn on the indoor unit.

The CHK pin and/or TEST pin on the indoor unit’s control PC board are shorted.

Forgot to install the nonvolatile memory (EEPROM) when replacing the indoor unit control PC board.

Mistakenly set the indoor unit address to Not Set in the remote control’s detailed setting mode.

When indoor unit addresses are duplicated.

•

•
•
•
•
•

There is a short, open, wrong contact or grounding of the indoor/outdoor operation line.

•

There is an error in the receiving circuit on the signal output PC board (optional control PC board).

•

Malfunctions of the outdoor unit

•
•

The thermistor inside the indoor unit is grounded.

•

4-6
4-7

Yes

Replace the outdoor unit control board
Replace the indoor unit control board

Yes

ACXA73-3129* : 4-Way Cassette Type (Type U3) Indoor Unit Control Board

ACXA73-3440* : Middle Static Pressure Duct Type (Type F3) Indoor Unit Control Board

OPTION

TEST Pin

DISP Pin

CHK Pin

EEPROM

OPTION

TEST Pin

CHK Pin

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 7

2020/01/29 21:17:44

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды