Panasonic S-3650PF3E Скачать руководство пользователя страница 303

Страница: 303 / 321

Wall Mount Use

■

Mounting the holder

1. Fasten the remote control holder with screws.

Remote control holder

Screws (supplied)

2. Slide the remote controller down into the holder.

•

Press

from the location you wish to mount the remote

Note

•

You cannot operate if the distance between the

remote controller and the receiver is greater than

that signals can travel.

■

Detaching the controller

1. Pull the remote controller up.

• Hold the remote controller with your hand and point its transmitter at the receiver. When the signal is received properly,

it will beep.

• Signals can travel a direct distance of 6 metres. This distance should be used only as a guide. It depends on battery strength.

• Make sure nothing is between the remote controller and the receiver that could block the signal.

• Do not leave the remote controller in direct sunlight, where the wind from the air conditioner can blow directly on it, or near

any other heat source.

• Take care not to drop, throw, or wash the remote controller with water.

• The signal from the remote controller may not be received in rooms with rapid start fluorescent lighting or inverter lights.

For more information, please contact the dealer where the product was purchased.

8-2-1-8. Using the Remote Controller

8-2-1-9. Pairing Addresses

controller and make sure the signal is received properl

When more than 1 indoor units are installed in the same room with a compatible remote controller, addresses can be set up to

avoid crosstalk.

You can control up to 6 indoor units individually by the supported remote controller by pairing the address on the remote

controller and the number on the address switch on the receiver.

There are separate address settings: receiver addresses for the receivers, and transmitter addresses for the remote controller.

Units will not be controlled if the setting do not match.

8-2-1-7

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 7

20/01/14 10:04:18

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды