Panasonic S-3650PF3E Скачать руководство пользователя страница 167 | Manualshive

Страница: 167 / 321

background image

1

1-11-2-1-16

4. TRANSPORT AND INSTALL THE OUTDOOR UNIT

Anchor bolt length

More than 25mm

More than 40mm

Base

More than

50mm

Model

A

B

C

D

U-36***

540 mm

160 mm

18.5 mm

330 mm

U-50***
U-60***

613 mm

131 mm

24 mm

360.5 mm

U-71***

A

B

C

D

5. REFRIGERANT INSTALLATION

1. Precautions during refrigerant installation.

Use clean pipes with no dust inside.

The pipe may corrode with the presence of

ﬂ

uorine dust which will adversely affect the refrigerant piping system due to deter ioration

of the refrigerant oil, etc.

This unit is speci

ﬁ

cally for R32. Ensure to adhere to the following items and install accordingly:

•

Use pipe cutters and

ﬂ

aring tools which are specially designed for use with R32.

•

When connecting with

ﬂ

aring tools, coat the

ﬂ

are section with ether-based oil.

•

Ensure to use

ﬂ

are nuts supplied with the unit when connecting this unit.

•

Only for storing or for open pipes.

•

Set the lower limit of the allowable pipe length to 3m.

•

Carefully handle the liquid refrigerant, as it may cause a frostbite.

•

Do not release refrigerants during the piping works for installing, re-installing and repairing refrigeration parts.

For indoor unit refrigerant piping installation, refer to the installation instruction manual that comes with that indoor unit.

Rear direction

Transporting

1. Transport the outdoor unit in its original packaging as close as possible to the installation location.

2. In the event that the unit needs to be lifted or suspended, use a rope or belt and use cloth or wood as padding to avoid dam aging the unit.

3. Use the side handles to carry the unit and be careful not to touch the fan with your hand or any objects.

Installation

1. Read the “Select the outdoor unit installation location” thoroughly before installing the outdoor unit.

2. When installing to a concrete or solid surface, use M10 or a W 3/8 bolts and nuts to secure the unit. Ensure that it installed upright on a horizontal plane.

(Use an anchor bolt for the installation as shown in the diagram below.)

3. Avoid installing on the slanted roof.

4. In the even where the roof is at risk of receiving oscillations or vibrations, secure the unit with a seismic isolating mou nt or vibration absorbing rubber.

5. The drain water will be discharged from the unit during heating or defrosting operation mode.

Select an appropriate location with good drainage system. (In the winter, there is risk of slipping due to freezing, and depending on the installation set up there

is risk of drain water running overhead.)

Please consult us if installing drain elbows.

In cold regions (where the outdoor temperature can drop to belo

w 0˚

for 2 to 3 consecutive days), the drain water may freeze and may prevent the fan from

operating. For this case, do not use the drain elbow.

U-36PZ3E5

U-50PZ3E5

U-60PZ3E5

U-71PZ3E5

Pipe outer diameter

)

4

/

1

(

5

3

.

6

).

n

i(

m

m

d

i

u

q

i

L

)

8

/

5

(

8

8

.

5

1

)

2

/

1

(

7

.

2

1

).

n

i(

m

m

s

a

G

0

4

0

3

0

2

5

1

)

m

(

h

t

g

n

e

l

e

p

i

p

m

u

m

ix

a

M
Maximum elevation

Outdoor unit is placed higher

(m)

0

2

5

1

Outdoor unit is placed lower

(m)

0

1

~

3

5

.

7

~

3

)

m

(

h

t

g

n

e

l

e

p

i

p

s

s

e

l-

e

g

r

a

h

C

Additional charge per 1 m

( )

7

1

5

1

0

1

Refrigerant charged at shipment

( )

0.87

1.14

1.15

1.32

Total refrigerant amount

( )

0.95

1.33

1.49

1.83

Speciﬁ

cation for pipe connecting indoor unit to outdoor unit.

Precautions when operating the 2/3-way valve for piping installation

Do not open the 2/3-way valve until the piping installation is completed.

•

It is closed during shipment.

•

When removing or tightening the gas tube

ﬂ

are nut, use 2 adjustable wrenches together:

one at the gas tube

ﬂ

are nut, and the other at part A.

Refer to the following table for the tightening torque of the 2/3-way valve

ﬂ

are nuts.

•

If the nuts are over tightened, they may cause the

ﬂ

ares to break or leak.

Do not add additional force to the valve’s cover.

•

Using spanners on the cover or valve itself (other than the hexagonal parts) may cause gas leakage.

Avoid using spanners on the cover or parts other than the hexagonal part of the valve.

Service port

Valve shaft

Valve cap

Flare nut

Valve A

A

A

Piping Thickness:

Size mm (in.)

6.35 (1/4)

9.52 (3/8)

12.7 (1/2)

15.88 (5/8)

Thickness. mm

> 0.8

> 0.8

> 0.8

> 1.0

If the pipe is shorter than 3m, the refrigerant may become over

ﬁ

lled and a problem such as abnormal high pressure

could occur.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 16

20/01/30 10:26:04

«
...
165
166
167
168
169
...
»

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Бренд: TCL Страницы: 143

Бренд: TCL Страницы: 18

Бренд: Vaillant Страницы: 136

Бренд: Valeo Страницы: 15

Бренд: York Страницы: 30

Бренд: ARCTIC WIND Страницы: 20

Бренд: Trane Страницы: 34

GWH09ACC-S6DBA1A/O

Бренд: Gree Страницы: 123

Бренд: Sinclair Страницы: 31

Бренд: Mitsubishi Страницы: 28

Бренд: Kaden Страницы: 16

Бренд: York Страницы: 20

Бренд: GE Страницы: 40

Бренд: Goodman Страницы: 48

Бренд: EUROM Страницы: 52

Бренд: Midea Страницы: 43

Бренд: Rheem Страницы: 12

Бренд: DENALI AIRE Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды