Panasonic S-3650PF3E Скачать руководство пользователя страница 238

Страница: 238 / 321

5-2-1-9

E08 Duplicate Indoor Unit Address Settings Error

Error Diagnosis

Error Detection Method

It is judged an error if the addresses of indoor units are duplicated.

For information on the procedures for replacing the nonvolatile memory (EEPROM) of the indoor unit, refer to the manual

that is packaged with the indoor unit service board.

•

The indoor unit address settings are duplicated in the remote control detailed settings mode.

The multiple unit DISP pin is shorted across the indoor unit whose address is Not Set.

•

Remove the short

Is the DISP pin on the indoor unit control PC board shorted?

1-2

1-1

Conduct checks prior to auto address setting.

Does E08 fail to go off even after running auto address setting again?

1-2

1-4

Yes

1-3

1-4

Indoor

unit

Do not make changes to indoor unit addresses with the detailed settings of the remote

controller.

Make them in the remote control address change mode.

control

PC board

The nonvolatile memory (EEPROM) on the indoor unit board has failed.

Replace the EEPROM.

ACXA73-3129* : 4-Way Cassette Type (Type U3)

ACXA73-3440* : Middle Static Pressure Duct Type

(Type F3)

OPTION

TEST Pin
CHK Pin

EEPROM

OPTION

TEST Pin
CHK Pin

ACXA73-3129* : 4-Way Cassette Type (Type U3) Indoor Unit Control Board

ACXA73-3440* : Middle Static Pressure Duct Type (Type F3) Indoor Unit Control Board

OPTION

TEST Pin

DISP Pin

CHK Pin

EEPROM

OPTION

TEST Pin

CHK Pin

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 9

2020/01/29 21:17:46

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды