Panasonic S-3650PF3E Скачать руководство пользователя страница 297 | Manualshive

Страница: 297 / 321

background image

8

8

8

8

8-1. Important Safety Instructions

WARNING

Installation Precautions

Do not install yourself
Installation should always be performed by your dealer or a professional service provider.
Electric shock or fire may result if an inexperienced person performs any installation or wiring procedures
incorrectly.

•

Use only specified air conditioners

•

Always use only air conditions specified by the dealer.

Precautions for Use

Do not touch switches with wet hands

•

Protect the remote controller from water Damage to the system can result.

•

Stop the system and turn the power off if you sense unusual smells or other irregularities

•

Do not swallow the battery.

•

Do not repair

•

Contact your dealer before moving the system

•

Moving and Repair Precautions

Electric shock and damage to the system can result.

Continuing operation when the system is out of order can result in electric shock, fire, and damage to the system.
Contact your dealer.

Never repair the system by yourself.

Contact your dealer or a professional service provider about moving and reinstalling the system.
Electric shock or fire may result if an inexperienced person performs any installation procedures incorrectly.

Press to change the fan speed.

Press to change the flap
direction.

ECONAVI

nanoeX

Use this to set the clock.

Press at the top center and then

slide down.

raises the temperature

setting 1 °C at a time.

lowers the temperature

setting 1 °C at a time.

Press to enable or disable

energy saving.

/

/

/

/

/

Use for operating with a timer.

RC

RESET

17. RC address

button

RC

ADR

Press to set addresses.

8-2. Optional Controller (Remote Controller)

Wireless (Infrared) Remote Controller

8-2-1-1. Names and Operations

1. Operation Display

Displays the operation status.
(The figure shows all the statuses.)

2. Start/Stop

button

Pressing this button once starts and
pressing again stops the operation.

3. Fan speed

button
4. Flap button

5. ECONAVI button

Press to set ECONAVI.

Press to set nanoe™ X.

Use this when connected to an
aftermarket fan.

6. nanoe™ X button

7. Ventilation button

8. Clock button

12. Mode Select

button

Press to switch the operation mode.

14. Filter button

16. RC reset button

Use this button after changing the
batteries.

13. Energy saving

button

15. Timer setting

buttons

Press to turn off the filter lamp on
the receiver.

9. Cover

11. Temperature

setting buttons

10. Transmitter

REMOTE CONTROLLER

From this page, the names of remote controller’s
buttons will be indicated with the above illustrations.
E.g.: Start/Stop button

1 remote controller can control a group of up to 8 indoor units. (See page 8-2-1-6)

CZ-RWS3

1

2

3

6

8

9

5

7

10

11

12
14

15
16

17

13

4

8-2-1-1

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 1

20/01/14 10:04:17

«
...
295
296
297
298
299
...
»

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Room Air Conditioners

Бренд: Fedders Страницы: 12

Бренд: Mesa Living Страницы: 37

LM012CI-115P432-1X

Бренд: Lennox Страницы: 44

Бренд: inventum Страницы: 100

Air Boss T1001 Module

Бренд: Trion Страницы: 23

Бренд: DCG Страницы: 18

Softaire RERV-80

Бренд: Air Specialties Страницы: 16

Бренд: EarthLinked Страницы: 11

Бренд: teca Страницы: 11

Бренд: Hantech Страницы: 180

Бренд: Acson Страницы: 140

ECD-SRT05TA-D2 Series

Бренд: MicroMetl Страницы: 18

Бренд: Cellartec Страницы: 35

Бренд: Daikin Страницы: 44

Бренд: Daikin Страницы: 36

Бренд: Gree Страницы: 112

Бренд: AirPicnic Страницы: 29

Бренд: Daikin Страницы: 355

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды