background image

1

Installation Instructions

ECD-SRT12TA-D2, ECD-SRT34TA-D2, ECD-SRT05TA-D2 Series

Read these instructions completely before attempting to install the Vertical 

Accessory Ultra Low Leak Economizer.

CONTENTS

Safety Consideration . . . . . . . . . . . . . . . . . . . . .1

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Economizer Sensor Usage. . . . . . . . . . . . . . . . . . . . .2

Accessories List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Wiring Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8 

W7220 Menu Structure. . . . . . . . . . . . . . . . . . . . .9-12 

Controller  Setup  and  Configuration.  .  .  .  .  .  .  .13-15 

Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Barometric Relief and Return Pressure

Drop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

*Jade W7220 Controller Addendum

*Certificate of Acceptance

Use QR Code Above to Access

SAFETY CONSIDERATIONS

Installation and servicing of air-conditioning equipment can be 

hazardous dur to system pressure and electrical components. Only 

trained  and  qualified  service  personnel  should  install,  repair,  or 

service air-conditioning equipment.
Untrained personnel can perform the basic maintenance funtions. 

All other operations should be performed by trained service 

personnel. When working on air-conditioning equipment, observe 

precautions in the literature, tags, and labels attached to the unit, 

and other safety precautions that may apply.
Follow allsafety codes. Wear safety glasses and work gloves. Use 

quenching cloth for unbrazing operations.
It is important to recognize safety information.  This is the safety-

alert symbol      .  When you see this symbol on the unit and in 

instructions or manuals, be alert to the potential for personal injury.

Understand the signal words DANGER, WARNING, CAUTION, 

and NOTE.  These words are used with the safety-alert symbol.

DANGER  identifies  the  most  serious  hazards  which 

will

 result 

in severe personal injury or death.  WARNING signifies hazards 

which 

could

 result in personal injury or death.  CAUTION is used 

to identify unsafe practices, which 

may

 result in minor  personal 

injury or product and property damage.  NOTE is used to highlight 

suggestions which 

will

 result in enhanced installation, reliability, or 

operation.

Small Rooftop Products

 

Select 3 to 12 ½ Tons

Accessory Ultra Low Leak Vertical Economizer

!

MicroMetl

California

& ASHRAE

Code

Compliant

WARNING

Electrical Shock Hazard

Can cause severe injury, death or property damage. Disconnect 

power supply before beginning wiring, or making wiring 

connections, to prevent electrical shock or equipment damage.

!

CAUTION

Equipment Damage Hazard

Electrostatic discharge can short equipment circuitry. Ensure 

that you are properly grounded before handling the unit.

!

Economizer

Package

Unit Chassis

48/50TC

48/50HC

48/50LC

50TCQ

48/50HCQ

Carrier

Bryant

ICP

Carrier

Bryant

ICP

Carrier

Carrier

Bryant

ICP

Carrier

Bryant

ICP

ECD-SRT12TA

Chassis 1

48/50TC 

A04,A05,A06,

B04,B05,B06

580J,558J 

04A,05A,06A,

04G,05G,06G

RGS,RAS

036,048,060

48/50HC A04 581J,551J 04A

RGH,RAH

036

48/50LC A04

50TCQ 

A04,A05

548J

04A,05A

RHS 

036, 048

50HCQ A04 549J 04A RHH 036

Chassis 2

48/50TC 

A07,B07

580J,558J

07A,07G

RGS,RAS 072

48/50HC 

A05,A06

581J,551J

05A,06A

RGH,RAH

048,060

48/50LC 

A05,A06

50TCQ

A06,A07

548J

06A,07A

RHS

060,072

50HCQ

A05,A06

549J

05A,06A

RHH

048,060

ECD-SRT34TA

Chassis 3

48/50TC

A08,D08

580J,558J

08A,08D

RGS,RAS

090,091

48/50HC A07

581J,551J

07A

RGH,RAH

072

N/A

N/A

N/A

N/A

50HCQ A07 549J 07A RHH 072

Chassis 4a

48/50TC

A09,A12,

D09,D12,D14

580J,558J

09A,12A,

09D,12D,14D

RGS,RAS

101,102,121

120,150

48/50HC

D08,D09 

581J,551J

09D,12D

RGH,RAH

090,120

48/50LC 07

50TCQ

D08,D09,D12

548J

08D,09D,12D

RHS

090,102,120

50HCQ 

D08,D09

549J

08D,09D

RHH

090,102

Chassis 4b

ECD-SRT05TA

Chassis 5

48/50TC D16 580J,558J 16D RGS,RAS 180 48/50HC D14 581J,551J 14D RGH,RAH 150

48/50LC 

08,09,12

N/A

N/A

N/A

N/A

N/A

N/A

Chassis 5

N/A

N/A

N/A

N/A

N/A

N/A

N/A

50TCQ D14

548J 14D

RHS 150

50HCQ D12 549J 12D RHH 120

Base Chasis/Curb Design (3-23 ton)

GENERAL (When ordered with controls)

The system utilizes the latest technology available for integrating 

the use of free cooling with mechanical cooling for packaged 

rooftop units. The solid-state control system optimizes energy 

consumption, zone comfort, and equipment cycling by operating 

the compressors when the outdoor-air temperature is too warm, 

integrating the compressor with outdoor air when free cooling 

is available, and locking out the compressor when outdoor-air 

temperature is too cold. Demand control ventilation is supported. 
This can be used with single or multiple speed indoor fans.
The MicroMetl Ultra Low Leak Economizer utilizes gear-driven 

technology with a direct-mount spring return actuator that will close 

upon loss of power. When ordering with controls, The Ultra Low 

Leak Economizer comes standard with a Mixed Air Sensor (Also 

called The Supply Air Temperature Sensor), and the option of 

Adjustable Dry Bulb, Enthalpy, Differential Adjustable Dry Bulb, and 

Differential Enthalpy Sensors. CO2 and Smoke Detectors Sensor 

are an additional field installed option.

Table 1

*QR Code

Содержание ECD-SRT05TA-D2 Series



















Отзывы: