Panasonic S-3650PF3E Скачать руководство пользователя страница 192

Страница: 192 / 321

2-3-1-11

(3)

(1)

(4)

* Auto address setting in Cooling mode cannot be done from the remote controller.

Auto Address Setting* from the Remote Controller (CZ-RTC4)

NOTE

Selecting each refrigerant system individually for auto address setting
Auto address setting for each system : Item code “A1”

button and

(1) Press the remote controller timer time

button at the same time.
(Press and hold for 4 seconds or longer.)

(2) Next, press either the temperature setting

(Check that the item code is “A1”.)

button.

(3) Use either the

auto address setting.

button to set the system No. to perform

Select the “O/D unit no.” by pressing the
or button.

2-3-1-6-3. Auto Address Setting Using the Remote Controller

Auto Address Setting from the High-spec Wired Remote Controller (CZ-RTC5B)

Select one of the “O/D unit no.” for auto address
by pressing the

or button.

Approximately 10 minutes are required.
When auto address setting is completed, the units
return to normal stopped status.

20:30 (THU)

[ ] START

CZ-RTC5B

(1)

CZ-RTC4

Keep pressing the

and

buttons

simultaneously for 4 or more seconds.
The “Maintenance func” screen appears on the LCD display.

If you wish to see the next screen instantly, press the

Press the

)

(

button to see each menu.

button.

Select “9. Auto address” on the LCD display and press
the

button.

Maintenance func

Sel.

20:30 (THU)

Page [

] Confirm

9. Auto address

10. Set elec. consumption

11. Set touch key

12. Check touch key

(3) The “Auto address” screen appears on the

Auto address

LCD display.
Change the “Code no.” to “A1” by pressing
the

or button.

O/D unit no.

Code no.

20:30 (THU)

Sel.

(4) Then press the

button.

(Auto address setting for one refrigerant system begins.)
(When auto address setting for one system is completed,

(2)

the system returns to normal stopped status.)
<Approximately 4 – 5 minutes is required.>
(During auto address setting, “

” is displayed on

the remote controller.
This message disappears when auto address setting is completed.)

(5) Repeat the same steps to perform auto address setting for each successive system.

(4)

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 11

2020/01/29 19:52:18

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды