Panasonic S-3650PF3E Скачать руководство пользователя страница 242

Страница: 242 / 321

5-2-1-13

E15 Automatic Address Alarm (The total capacity of indoor units is too low.)

Error Detection Method

It is judged an error the total capacity of indoor units replied by communication is lower than that of outdoor unit.

Connecting indoor unit

The total capacity of indoor units is lower than that of outdoor unit.

•

Some indoor unit(s) are connected but power is not turned on.

•

The CHK pin (CN062/CN071) and/or TEST pin (CN064) of the indoor unit is shorted when its power is turned on.

•

For information on the remote control’s detailed settings, refer to the Reference Materials.

•

The alarm also occurs when the indoor unit cannot be recognized (indoor unit only blackout, disconnection of indoor/outdoor

operation line, etc.) during auto address setting.

•

For information on the procedures for replacing the nonvolatile memory (EEPROM) of the indoor unit, refer to the manual

that is packaged with the indoor unit service board.

•

Is the indoor unit powered off?

1-1

3-1 Was the number of indoor units changed after auto address setting

finished?
Conduct checks prior to auto address setting.

3-2

Power on
2-1

Yes

Is the indoor/outdoor wiring connected correctly?

3-1

2-1

Yes

Correct the wiring

Indoor/

outdoor

wiring

3 No. of

Indoor

Units

1 Power

Source

2. Error Diagnosis

3-2

Yes

4-1

Replace wireless remote control parts including wiring.

4-4

Is the LED blinking on the indoor unit’s control PC board?

4-5

4-6

Disconnect the connector mentioned above on the control PC board

of the indoor unit control PC board and see whether the E15 goes off

after several minutes. (When doing so, if two remote controllers are

being used and the wireless remote controller is the main remote

controller, set the other remote controller as the main.)

Check all items under the section “Check Prior to Auto Address Setting”.

5-1

The nonvolatile memory (EEPROM) on the indoor unit’s control board is either not installed,

improperly installed or the nonvolatile memory is faulty. Correct this or after replacing the

nonvolatile memory, write model data to it in the remote control detailed settings mode.

4-7

Are the CHK Pin and TEST Pin on the indoor unit control board

short-circuited?

Be sure that the detailed setting items are made at factory setting.

4-2

4-1

Is the wireless remote controller connected to on the indoor unit’s

control PC board?

4-3

4-5

Yes

4-6

Remove the short
4-3

Yes

4-2
Correct the setting

Run the auto address

Yes

4-4

Yes

4-6

4 Indoor

unit

control

PC board

unit control

5 Outdoor

PC board

4-7

Yes

5-1

Factory setting
Item code

Item

Value

99
99
99

Indoor unit capacity

Indoor unit address
Group conrol address

System address

12
13
14

[ U3, F3 ]

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 13

2020/01/29 21:17:47

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды