manualshive.com logo in svg

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Panasonic S-3650PF3E - Мощный и надежный продукт с выдающимися характеристиками. Теперь вы можете с легкостью узнать больше о его технических данных и обслуживании, скачав бесплатный руководство по эксплуатации с manualshive.com. Не упустите шанс загрузить его и улучшить свой пользовательский опыт.

Поделиться
Скачать
background image

2

2

2-4-1-2

2-4.  Outdoor Units
2-4-1-1.  CHECKS AFTER INSTALLATION HAVE COMPLETED

Is there a short circuit with the intake air flow?

Is the insulation secure? (Refrigerant piping)

Are there any errors with the wiring?

Are the terminal screws loose? Tightening torque (Unit: N•m {k

g

f•cm})

M4...1.57~1.96 {16~20}, M5...1.96~2.45 {20~25}

Is the drain water flowing smoothly?

Is the insulation material properly installed?

Is the earth wire securely connected?

Are the terminal board cover, control board cover and the indoor unit air conditioner firmly fixed and was the installation

 

completed without any leakage from the refrigerant?

Are the indoor and outdoor units secured firmly installed with bolts at secured locations?

User inspection places

Serviceman inspection

places

2-4-1-2. REGARDING DELIVERY TO THE CUSTOMER

Request the customer to review the operating instructions and explain the operating method for the product.

In addition, it is also recommended that regular inspection checks are agreed upon for maintenance.

Refer to the installation instruction manual provided with the indoor unit for the specifications on the indoor unit installati

on.

Check the following items after completing installation.

• Grill cleaning

• Exterior cleaning

•

Check the operating status

•

Clean the drain pan or things related to the water discharge

• Heat exchanger cleaning

Note : In the case that inter-unit wiring is 30m or longer, you cannot 

           pump-down.

          (lt may trigger the operation of the overload protection device.)

          In this case, perform Pump-Down with Pump-Down device.

If you do not stop the compressor operation, and if the valve is open and remove the 

refrigerant pipes, the air may be sucked into the system and causes extreme high 

temperature in the refrigerant cycle. This may result in rupture or injury, etc.

CAUTION

This outdoor unit cannot collect more than the rated refrigerant

amount as shown by the nameplate on the back.

If the amount of refrigerant is more than that recommended,

do not conduct a Pump-Down.

In this case use another refrigerant collecting system.

Pay a special attention on the rotating of the fan while operating.

Caution in the  Pump-Down operation, stop the compressor before removing the 

refrigerant pipes.

2-4-1-3. Caution for Pump-Down

1 

  

Stop operation of the unit (cooling, heating etc.).

2   Connect the pressure gauge to the service port of the gas wiring valve.
3   Short-circuit CN-S continously between 1 second and seconds, Pump-Down begins and the unit starts operating.
4   Fully close the liquid side valve 2-3 minutes later.
     The Pump-Down will begin.
5   When the pressure gauge drops to 0.1-0.2MPa, close the gas side valve tight and short-circuit the CN-S in again.
     Pump-Down operation completed.
Control stop condition
-600 seconds after the Pump-Down operation starts

CN-S

Pump down means refrigerant gas in the system is returned to the outdoor unit.
Pump down is used when the unit is to be moved, or before servicing the refrigerant circuit.

(1) Remove the top panel 

      by unfastening five screws. 

(1) To remove the electrical 

      component box cover, 

      press the latches on the  

      cover in the direction of the  

      arrow while holding the 

      handle with one hand.

How to perform Pump-Down (Refrigerant recovery) properly

Screws (× 5)

Electrical component box cover

Latches

Handle

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb   2

2020/01/29   19:52:20

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Argo AWI726HL Technical Data & Service Manual preview
AWI726HL
Бренд: Argo Страницы: 38
Turbo Air TAS-36EHU Owner'S Manual preview
TAS-36EHU
Бренд: Turbo Air Страницы: 19
Midea V4+R Series Service Manual preview
V4+R Series
Бренд: Midea Страницы: 104
GE Appliances AJCQ10ACDH5 Owner'S Manual And Installation Instructions preview
Appliances AJCQ10ACDH5
Бренд: GE Страницы: 16
Waeco CoolAir CA-800 Manual preview
CoolAir CA-800
Бренд: Waeco Страницы: 33
DeDietrich MOSE 20 User Manual preview
MOSE 20
Бренд: DeDietrich Страницы: 12
Fakir prestige AC 9 Operating Instructions Manual preview
prestige AC 9
Бренд: Fakir Страницы: 56
Vaillant climaVAIR V 7-050 NW Installation Manual preview
climaVAIR V 7-050 NW
Бренд: Vaillant Страницы: 24
Carrier Comfort 24ACA3 Product Data preview
Comfort 24ACA3
Бренд: Carrier Страницы: 22
Lennox XC13 018 Unit Information preview
XC13 018
Бренд: Lennox Страницы: 14
Carrier 38QHG009D8S Series Installation Manual preview
38QHG009D8S Series
Бренд: Carrier Страницы: 92
Adler Europe AD 7922 User Manual preview
AD 7922
Бренд: Adler Europe Страницы: 80
Hitecsa CCHBA/CCHA 1201 Installation, Operation & Maintenance Manual preview
CCHBA/CCHA 1201
Бренд: Hitecsa Страницы: 35
Signature S40006 Safety & Instruction Manual preview
S40006
Бренд: Signature Страницы: 12
ACPro GMV-N07G/A3A-D Owner'S Manual preview
GMV-N07G/A3A-D
Бренд: ACPro Страницы: 20
Admiral AW-24CM3FM Use And Care Manual preview
AW-24CM3FM
Бренд: Admiral Страницы: 38
Daikin FXFQ20M8V3B Installation And Operation Manual preview
FXFQ20M8V3B
Бренд: Daikin Страницы: 16
Daikin FXFQ20BVEB Installation And Operation Manual preview
FXFQ20BVEB
Бренд: Daikin Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды