Panasonic S-3650PF3E Скачать руководство пользователя страница 62

Страница: 62 / 321

1-9-2

Resistance within the unit (Pa

)

Noise with only external

air intake dB(A)

External Air Intake Volume (m

/h)

External Air Intake Volume & Resistance Within Unit/

Operation Noise Characteristics

With the External Air Intake Chamber Attached

Use the following diagram along with the section "1-9-1. Precautions Regarding External

Air Intake"

In a Case of External Air Intake Using Air Intake Chamber (CZ-FDU3+CZ-ATU2)

Sample selection of booster fans

In a case of necessity at 200m

/h of external air intake:

Therefore, a booster is required to save a total 95 Pa of static pressure.

1. Resistance within the unit

Diagram from "Resistance within the unit" 55 Pa

2. Duct resistance in case of duct with 4m length

Duct resistance

Diagram from "Air Flow Volume for

Flexible Cylindrical Duct-Pressure Loss"

(=10 Pa/m × 4m)

40 Pa

Total 95 Pa

Calculate the operation noise when external air is being fed by combining the noise when only external air is being fed as

shown in the diagram for operation noise characteristics and the operation noise of the unit as stipulated in the catalogue.

The amount of external air that is possible to feed when external air intake chamber is in use

(CZ-FDU3+CZ-ATU2)

* The operation noise for models that use small units is lower, so use values that are within the range shown in the

* For S-6071PU3E (60) and S-6071PU3E (71), see the Combination Table items 60 and 71 on page 15.

above table. Using values that exceed these will result in noise when only external air is fed being louder than the

noise emitted from the unit.

Permissible air intake

volume (m

/h)

The operation noise conforms to JIS standards and constitute measurements taken in an anechoic chamber 1.5m directly

below the indoor unit. Under normal circumstances, the diagram shown above is greater owing to the effects of surrounding

noise and reverberation when the unit is actually installed.

100

90
80
70
60
50
40
30
20
10

-10

50
40
30
20

100

150

200 240

Resistance within the unit

(High speed wind)

Operation noise

(External air intake only)

Filter chamber

(

CZ-FDU3

)

Kit for external air intake (for chamber)

(CZ-ATU2)

Connection duct: diameter ø100

Type

180

S-3650PU3E

190 (60)*

240 (71)*

S-6071PU3E

SM830231-02_Single_

欧州

.indb 263

2014/09/19 13:21:42

CAUTION

1-9-2-1. 4-Way Cassette (Type U3)

When an External Air Intake Flange (ø100) is in Use

External Air Intake Volume and Resistance and

Operation Noise Characteristics within the Unit

• Calculate the operation noise when external air is being fed by combining the noise when only external air

is being fed as shown in the graph for operation noise characteristics and the operation noise of the unit as

stipulated in the catalogue.

• The operation noise conforms to JIS standards and constitute measurements taken in an anechoic chamber

1.5 m directly beneath the indoor unit. Under normal circumstances, the values shown here are greater owing

to the effects of surrounding noise and reverberation when the unit is actually installed.

The amount of external air that is possible to feed when it is fed directly into the unit (ø100)

Type

S-3650PU3E S-6071PU3E

Permissible Air Intake
Volume (m³/h)

17 (60)*

18 (71)*

* For S-6071PU3E (60) and S-6071PU3E(71), see the Combination Table items 60 and 71 on page 15.

NOTE

The operation noise for models that use small units is lower, so use values that are within the range shown in the

above table. Using values that exceed these will result in noise when only external air is fed being louder than the

noise emitted from the unit.

With the External Air Intake Flange Attached

Resistance

within

the

Unit

External Air Intake Volume (m

/h)

Noise

with

only

Exter

nal

Air

Intak

dB(A)

Operation Noise

(External Air Intake Only)

100

Duct (ø100) for Connecting

the External Air Intake Flange

Type U3

1-9-2. External Air Intake Volume & Resistance Within Unit / Operation Noise Characteristics

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 2

20/01/30 10:24:55

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды