Panasonic S-3650PF3E Скачать руководство пользователя страница 147

Страница: 147 / 321

1-11-1-2-28

APPENDIX

WARNING

●

For safety, be sure to turn the air conditioner off and

also to disconnect the power before cleaning.

●

Do not pour water on the indoor unit to clean it. This will

damage the internal components and cause an electric

shock hazard.

Air intake and outlet side (Indoor unit)

Clean the air intake and outlet side of the indoor unit with a

vacuum cleaner brush, or wipe them with a clean, soft cloth.
If these parts are stained, use a clean cloth moistened with

water. When cleaning the air outlet side, be careful not to force

the vanes out of place.

CAUTION

Never use solvents or harsh chemicals when cleaning

the indoor unit. Do not wipe plastic parts using very hot

water.
Some metal edges and the fins are sharp and may

cause injury if handled improperly; be especially careful

when you clean these parts.
The internal coil and other components of outdoor

unit must be cleaned regularly. Consult your dealer or

service center.

Air filter

The air filter collects dust and other particles from the air and

should be cleaned at regular intervals or when the filter

indication ( ) on the display of the remote controller (wired

type) shows that the filter needs cleaning. If the filter gets

blocked, the efficiency of the air conditioner drops greatly.

Type

Period

2 weeks

After Cleaning

After the air ﬁlter is cleaned, reinstall it in its o

riginal

position.
Be sure to reinstall in reverse order.

Press the Filter reset button.

The (Filter) indicator on the display goes out.

[In the case of High-spec Wired Remote Controller and

Wired Remote Controller]

Refer to the Operating Instructions attached to the

optional High-spec Wired Remote Controller or optional

Wired Remote Controller.

NOTE

The frequency with which the filter should be cleaned depends

on the environment in which the unit is used.

Clean the filter frequently for best performance in the area of

dusty or oil spots regardless of filter status.

Timer Remote Controller

Filter indicator

Filter reset button

High-spec Wired

Remote Controller

Wired Remote

Controller

Filter indicator

<How to remove the filter>

Remove the filter in reverse order of the

section “Install the Filter” on page 1-11-1-2-4.

<How to clean the filter>

Use a vacuum cleaner to remove light dust. If there is sticky

dust on the filter, wash the filter in lukewarm, soapy water, rinse

it in clean water, and dry it.

In case of Installing the Duct (field supply)

Type

Period

(Depends on filter’s specifications)

When cleaning the air filter, consult your dealer or service

center.

Care: After a prolonged idle period

Check the indoor and outdoor unit air intakes and outlets for

blockage; if there is a blockage, remove it.

Care: Before a prolonged idle period

CAUTION

Certain metal edges and the condenser fins are sharp

and may cause injury if handled improperly; special care

should be taken when you clean these parts.
The internal coil and other components must also be

The internal coil and other components must also be

cleaned periodically. Consult your dealer or service

center.

cleaned periodically. Consult your dealer or service

center.

Operate the fan for half a day to dry out the inside.
Disconnect the power supply and also turn off the circuit

breaker.
Clean the air filter and replace it in its original position.
Outdoor unit internal components must be checked and

cleaned periodically. Contact your local dealer for this service.

●

●
●

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 28

20/01/30 10:25:55

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды