Panasonic S-3650PF3E Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 321

background image

1

1-10-1-2-1

General Precautions on Wiring

NOTE

*

With ring-type wire terminal.

Check the type of the outdoor unit terminal board

as illustrated below and make connection.

Recommended Wire Length and Wire Diameter for Power Supply System

2. Type F3

S-3650PF3E, S-6071PF3E

The remote control wiring and the inter-unit control wiring should be wired apart from the inter-unit power wiring.
Use shielded wires for inter-unit control wiring between units and ground the shield on both sides.

(1) Before wiring, confirm the rated voltage of the unit as shown on its nameplate, then carry out the wiring closely following the

wiring diagram.

WARNING

(2) This equipment is strongly recommended to be installed with Earth Leakage Circuit Breaker (ELCB) or Residual Current

Device (RCD). Otherwise, it may cause electrical shock and fire in case of equipment breakdown or insulation breakdown.

Earth Leakage Circuit Breaker (ELCB) must be incorporated in the fixed wiring in accordance with the wiring regulations.

The Earth Leakage Circuit Breaker (ELCB) must be an approved circuit capacity, having a contact separation in all poles.

(3) To prevent possible hazards from insulation failure, the unit must be grounded.

(4) Each wiring connection must be done in accordance with the wiring system diagram.

Wrong wiring may cause the unit to misoperate or become damaged.

(5) Do not allow wiring to touch the refrigerant tubing, compressor, or any moving parts of the fan.

(6) Unauthorized changes in the internal wiring can be very dangerous. The manufacturer will accept no responsibility for any

damage or misoperation that occurs as a result of such unauthorized changes.

(7) Regulations on wire diameters differ from locality to locality. For field wiring rules, please refer to your LOCAL ELECTRICAL

CODES before beginning.

You must ensure that installation complies with all relevant rules and regulations.

(8) To prevent malfunction of the air conditioner caused by electrical noise, care must be taken when wiring as

follows:

CAUTION

Check local electrical codes and regulations before wiring. Also, check any specified instruction or

limitations.

Control wiring

(D) Remote control wiring

(C) Inter-unit (between Integrated

control system and indoor units)

control wiring

(E) Remote control wiring for group

control

0.75 mm

2

0.75 mm

2

(AWG #18)

Use shielded wiring*

(AWG #18)

0.75 mm

2

(AWG #18)

Max. 1,000 m

(D) + (E) : Max. 500 m (E) : Max. 200 m

The above descriptions can be used for the model CZ-RTC4 or CZ-RTC5B. For

other remote controllers, refer to the manual of each unit.

Indoor unit

(Type of 3-line connection [1, 2 and 3] with indoor and outdoor units)

Type

Connection cable between outdoor and indoor unit

1.5 mm

2

F3

Max. 40 m

L

N

1

2

3

Connection cable between

outdoor and indoor unit

Power supply cable

If 1, 2 and 3 are shown on the terminal

board, it is for 3-line connection.

(F) Outdoor unit U-36 ~ 71PZ3E5

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 1

20/01/30 10:24:57

«
...
68
69
70
71
72
...
»

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Versaflo TR-600 Series

Бренд: 3M Страницы: 3

Бренд: Vax Страницы: 7

Бренд: INVENTOR Страницы: 136

Бренд: Orbegozo Страницы: 143

Бренд: York Страницы: 30

Бренд: ARCTIC WIND Страницы: 20

Бренд: Trane Страницы: 34

Бренд: Vaporetto Страницы: 14

Бренд: Techwall Electronics Страницы: 4

Бренд: Daikin Страницы: 140

Бренд: Lennox EMEA Страницы: 32

Бренд: Rheem Страницы: 60

Бренд: Daikin Страницы: 8

Бренд: Daikin Страницы: 20

Бренд: Daikin Страницы: 16

Бренд: Daikin Страницы: 28

Бренд: Daikin Страницы: 78

Бренд: Daikin Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды