Panasonic S-3650PF3E Скачать руководство пользователя страница 83

Страница: 83 / 321

1-11-1-1-7

HOW TO PROCESS TUBING

Must ensure mechanical connections be accessible for

maintenance purposes.

●

Connecting the Refrigerant Tubing

Use of the Flaring Method

Many of conventional split system air conditioners employ the

flaring method to connect refrigerant tubes that run between

indoor and outdoor units. In this method, the copper tubes are

flared at each end and connected with flare nuts.

Flaring Procedure with a Flare Tool

(1) Cut the copper tube to the required length with a tube

cutter. It is recommended to cut approx. 30 – 50 cm longer

than the tubing length you estimate.

(2) Remove burrs at each end of the copper tubing with a tube

reamer or a similar tool. This process is important and

should be done carefully to make a good flare. Be sure to

keep any contaminants (moisture, dirt, metal filings, etc.)

from entering the tubing.

After

Before

Deburring

Copper

tubing

Reamer

NOTE

When reaming, hold the tube end downward and be sure that

no copper scraps fall into the tube.
(3) Remove the flare nut from the unit and be sure to mount it

on the copper tube.

(4) Make a flare at the end of the copper tube with a flare tool.

Flare nut

Copper

tubing

Flare tool

NOTE

When flared joints are reused, the flare part shall be re-fabricated.

A good flare should have the following characteristics:

● inside surface is glossy and smooth

● edge is smooth

● tapered sides are of uniform length

Caution Before Connecting Tubes Tightly

(1) Apply a sealing cap or water-proof tape to prevent dust or

water from entering the tubes before they are used.

(2) Be sure to apply refrigerant lubricant (ether oil) to the

inside of the flare nut before making piping connections.

This is effective for reducing gas leaks.

Apply refrigerant lubricant.

(3) For proper connection, align the union tube and flare tube

straight with each other, then screw on the flare nut lightly

at first to obtain a smooth match.

Flare nut

Union

● Adjust the shape of the liquid tube using a tube bender at the

installation site and connect it to the liquid tubing side valve

using a flare.

NOTE

When connecting flare at indoor side, make sure that the flare

connection is used only once. If torqued up and released, the

flare must be remade. Once the flare connection was torqued

up correctly and leak test was made, thoroughly clean and

dry the surface to remove oil, dirt and grease by following

instructions of silicone sealant. Apply neutral cure & ammonia-

free silicone sealant that is non-corrosive to copper & brass to

the external of the flared connection to prevent the ingress of

moisture on both the gas & liquid sides. (Moisture may cause

freezing and premature failure of the connection.)

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 7

20/01/30 10:25:06

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды