Panasonic S-3650PF3E Скачать руководство пользователя страница 108

Страница: 108 / 321

1-11-1-1-32

Check Before Requiring Services

Symptom

Cause

Remedy

Air conditioner does not run
at all although power is turned
on.

Power failure or after power failure

Press ON/OFF operation button on remote
controller again.

Operation button is turned off.

Switch on power if breaker is turned off.

If breaker has been tripped, consult your dealer
without turning it on.

Fuse blow out.

If blown out, consult your dealer.

Poor cooling or heating
performance

Air intake or air discharge port of indoor
and outdoor units is clogged with dust or
obstacles.

Remove dust or obstruction.

Fan speed switch is set to “Low”.*

Change to “Medium” or “High”.*

Improper temperature settings

See “ Tips for Energy Saving”.

Room is exposed to direct sunlight in
cooling mode.
Doors and /or windows are open.
Air filter is clogged.

See “Care and Cleaning” on page 1-11-1-1-30.

Too much heat sources in room in
cooling mode.

Use minimum heat sources and in a short time.

Too many people in room in cooling
mode.

Reduce temperature settings or change to “Medium”
or “High”.*

* Fan speed display on the remote controller

High

(CZ-RTC4),

(CZ-RTC5B, CZ-RTC6*)

Medium :

(CZ-RTC4),

(CZ-RTC5B, CZ-RTC6*)

Low

(CZ-RTC4),

(CZ-RTC5B, CZ-RTC6*)

If your air conditioner still does not work properly although you checked the points as described above, first stop the operation

and turn off the power switch. Then contact your dealer and report the serial number and symptom. Never repair your air

conditioner by yourself since it is very dangerous for you to do so.

Tips for Energy Saving

Avoid

Do not block the air intake and outlet of the unit. If either is obstructed, the unit will not work well, and may be damaged.

Do not let direct sunlight into the room. Use sunshades, blinds or curtains. If the walls and ceiling of the room are warmed by the

sun, it will take longer to cool the room.

Always try to keep the air filter clean. (See “Care and Cleaning” on page 1-11-1-1-30.) A clogged filter will impair the performance

of the unit.

To prevent conditioned air from escaping, keep windows, doors and any other openings closed.

NOTE

Should the power fail while the unit is running

If the power supply for this unit is temporarily cut off, the unit will automatically resume operation once power is restored using the same

settings before the power was interrupted.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 32

20/01/30 10:25:20

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды