Panasonic S-3650PF3E Скачать руководство пользователя страница 4

Страница: 4 / 321

WARNING

•

When performing piping work, do

not mix air except for specified

refrigerant

)

in refrigeration

cycle. It

causes capacity down, and

risk of

explosion and injury due to

cycle.

high

tension inside the refrigerant

• If the refrigerant comes in contact

with a flame, it produces a toxic

gas.

• Do not add or replace refrigerant

other than specified type. It may

cause product damage, burst and

injury, etc.

• Ventilate the room immediately, in the

event that is refrigerant gas leaks during

the installation. Be careful not to allow

contact of the refrigerant gas with a

flame as this will cause the generation

of toxic gas.

• Keep all tubing runs as short as

possible.

• Use the flare method for connecting

tubing.

• Apply refrigerant lubricant to the

matching surfaces of the flare and union

tubes before connecting them, then

tighten the nut with a torque wrench for

a leak-free connection.

• Check carefully for leaks before starting

the test run.

• Do not leak refrigerant while piping work

for an installation or re-installation, and

while repairing refrigeration parts.

Handle liquid refrigerant carefully as it

may cause frostbite.

• Under no circumstances shall potential

sources of ignition be used in the

searching or detection of refrigerant

leaks.

• A halide torch (or any other detector

using a naked flame) shall not be used.

• Electronic leak detectors may be used

to detect refrigerant leaks but, the

sensitivity may not be adequate, or

may need re-calibration. (Detection

equipment shall be calibrated in a

refrigerant-free area.)

• Ensure that the detector is not a

potential source of ignition and is

suitable for the refrigerant used

• Leak detection equipment shall be set

at a percentage of the lower flammable

limit (LFL) of the refrigerant and shall be

calibrated to the refrigerant employed

and the appropriate percentage of gas

(25 % maximum) is confirmed.

•

Leak detection fluids are suitable for

use with most refrigerants but the use of

detergents containing chlorine shall be

avoided as the chlorine may react with

the refrigerant and corrode the copper

pipe-work.

• If

leak is suspected, all naked flames

shall be removed/extinguished.

• If

leakage of refrigerant is found which

requires brazing, all of the refrigerant

shall be recovered from the system, or

isolated (by means of shut off valves)

in a part of the system remote from the

leak. Oxygen free nitrogen (OFN) shall

then be purged through the system both

before and during the brazing process.

When Servicing

• Contact to the sales dealer or service

dealer for a repair.

• Be sure to turn off the power before

servicing.

• Turn the power OFF at the main

power box (mains), wait at least 10

minutes until it is discharged, then

open the unit to check or repair

electrical parts and wiring.

• Keep your fingers and clothing away

from any moving parts.

• Clean up the site after you finish,

remembering to check that no metal

scraps or bits of wiring have been left

inside the unit.

01_301040_EU_Eng.indb 4

2018/2/1 15:30:10

WARNING

• This product must not be

modified or disassembled under

any circumstances. Modified or

disassembled unit may cause fire,

electric shock or injury.

• Do not clean inside the indoor and

outdoor units by users. Engage

authorized dealer or specialist for

cleaning.

• In case of malfunction of this

appliance, do not repair by

yourself. Contact to the sales

dealer or service dealer for a

repair and disposal.

CAUTION

• Ventilate any enclosed areas

when installing or testing the

refrigeration system. Leaked

refrigerant gas, on contact

with fire or heat, can produce

dangerously toxic gas.

• Confirm after installation that

no refrigerant gas is leaking. If

the gas comes in contact with a

burning stove, gas water heater,

electric room heater or other

heat source, it can cause the

generation of toxic gas.

Others

When disposal of the product, do follow

the precautions in “1

. R

ecovery

”

page 1-11-

-6 and comply

with national

regulations.

WARNING

•

Do not sit or step on the

unit. You may fall down

accidentally.

CAUTION

•

Do not touch the air inlet or

the sharp aluminum fins of

the outdoor unit. You may get

injured.

•

Do not stick any object into

the FAN CASE.

You may be injured and the

unit may be damaged.

01_301040_EU_Eng.indb 5

2018/2/1 15:30:10

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 3

2020/01/29 21:46:01

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды