Panasonic S-3650PF3E Скачать руководство пользователя страница 172

Страница: 172 / 321

1-12-2-1-1

1-12. Capacity Table
2. Heating Capacity Performance Data
Type U3 Series

TC :Heating Capacity
IPT :Heating Power Consumption

unit : kW

Outdoor air intake temp(°C W.B.)

Model

Power

Source

Ambient

Return

Air

-16°C

-8°C

6°C

10°C

15°C

IPT

S-3650PU3E

(S-3650PU3E(36))

U-36PZ3E5

220V-230V-240V

50Hz 1phase

2.6

0.817

3.3

0.877

4.7

1.00

5.1

1.04

5.6

1.10

2.5

0.869

3.2

0.933

4.6

1.06

5.0

1.10

5.6

1.17

2.5

0.924

3.2

0.992

4.5

1.13

4.9

1.17

5.5

1.24

S-3650PU3E

(S-3650PU3E(50))

U-50PZ3E5

220V-230V-240V

50Hz 1phase

3.7

1.35

4.7

1.50

6.5

1.73

7.0

1.83

7.7

1.92

3.6

1.44

4.6

1.60

6.4

1.84

6.9

1.94

7.6

2.05

3.6

1.52

4.5

1.70

6.3

1.95

6.8

2.06

7.4

2.15

S-6071PU3E

(S-6071PU3E(60))

U-60PZ3E5

220V-230V-240V

50Hz 1phase

4.6

1.46

5.5

1.69

7.1

2.09

7.7

2.23

8.1

2.11

4.6

1.54

5.4

1.78

7.0

2.20

7.6

2.35

8.0

2.11

4.5

1.65

5.3

1.91

6.9

2.35

7.4

2.35

7.9

2.11

S-6071PU3E

(S-6071PU3E(71))

U-71PZ3E5

220V-230V-240V

50Hz 1phase

4.7

1.66

5.8

1.88

8.2

2.30

8.8

2.40

8.9

2.25

4.7

1.78

5.8

2.02

8.1

2.40

8.7

2.50

8.8

2.25

4.5

1.90

5.6

2.16

7.8

2.50

8.2

2.50

8.6

2.25

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 1

20/01/30 10:26:08

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды