Panasonic S-3650PF3E Скачать руководство пользователя страница 194

Страница: 194 / 321

2-3-1-13

Indoor unit address

<If multiple indoor units are connected to 1 remote controller (group control)>

Number changes to indicate which

indoor unit is currently selected.

(1)

button for 4 seconds or

Press and hold the

button and

longer (simple settings mode).
“ALL” is displayed on the remote controller.
Next, press the button.

)

(

)

(
(4) The address is displayed for 1 of the indoor units which is connected

to the remote controller. Check that the fan of that indoor unit starts
and that air is discharged.

(5) Press the

unit in sequence.

button again and check the address of each indoor

(6) Press the

button again to return to normal remote controller mode.

Indoor unit address

Number changes to indicate which

indoor unit is currently selected.

(1)

CZ-RTC4 (Timer remote controller)
<If 1 indoor unit is connected to 1 remote controller>

button for 4 seconds or

Press and hold the

button and

longer (simple settings mode).
The address is displayed for the indoor unit that is connected to
the remote controller.

)

(

(Only the address of the indoor unit that is connected to the remote
controller can be checked.)
PPress the button again to return to normal remote controller
mode.

)

(

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 13

2020/01/29 19:52:18

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды