manualshive.com logo in svg

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Panasonic S-3650PF3E - Мощный и надежный продукт с выдающимися характеристиками. Теперь вы можете с легкостью узнать больше о его технических данных и обслуживании, скачав бесплатный руководство по эксплуатации с manualshive.com. Не упустите шанс загрузить его и улучшить свой пользовательский опыт.

Поделиться
Скачать
background image

1

1-11-1-1-27

ECONAVI TEST OPERATION

Preparation:  Refer to the manuals of the indoor unit and turn 

on the main power switch in advance. 

 

 Human detection cannot be made for approx. 
90 seconds when switched on the power

 

 because the human detection sensor is set in 
initial setup.

1.  Press three buttons.
 Keep pressing the 

 , 

 and 

 buttons 

simultaneously for more than 4 seconds.

 

The “Maintenance func” menu appears on the screen.

2.

 

Select “0. ECONAVI info.” from the menu command.

 

By pressing the 

 / 

 buttons, select 

“0. ECONAVI info.” and press the 

 button.

3.

 

Select “Error found” from the menu command.

 

By pressing the 

 / 

 buttons, select “Error 

found” and press the 

 button.

4.

 

Check the sensor status shows “Normal”.

 

(By pressing the 

 / 

 buttons, the status of 

each indoor unit can be scrolled on the screen.)

 

The sensor status of all indoor units are displayed.

 

•  

“Normal”: The sensor on the panel for cassette 

(ECONAVI type) works normally.

 

•  

“Preparing”: The sensor on the panel for cassette 

(ECONAVI type) is set in initial setup.
Confirm that “Normal” appears within 90 seconds.

 

•  

“Unsupported”: Indoor units not available for ECONAVI 

function.

The test run procedure described above is over. If any 
display appears other than “Normal” or “Preparing” even 
though the ECONAVI panel is connected, follow the Step 5 
below. 
* “1-1”, “1-2” mean indoor unit No. If the indoor unit is without 

ECONAVI panel, “Not connected” appears.

* “Sensor 1” means optional ECONAVI sensor  

(CZ-CENSC1). If not connected, “Not connected” appears 
besides “Sensor 1” on the screen.

5.

 

If the sensor status shows other than “Normal”, 
“Preparing”,

 

If the sensor status shows “Error” or “Not connected” 
although the panel for cassette (ECONAVI type) is 
connected, the following symptom may have occurred. 
Specify the applicable indoor unit and check the sensor.

 

“Error”: The sensor may possibly be damaged.

 

”Not connected”: The wiring between the indoor unit and 
sensor may possibly be disconnected.

  *  The specified indoor unit can be confirmed by the flap 

operation.
Confirmation method:

1

 Finish the maintenance function.

Press the 

 button to show the maintenance 

function display and then press the 

 button.

2

 Operate the flap.

By pressing the 

 button, select the applicable 

“Indoor Unit No.” in the list of “2. FLAP” and then 
make flap setting. The indoor unit which responds to 
the flap setting becomes available.  

 

When the indoor unit is specified, turn off the main 
power switch and disconnect the connector of sensor 
wiring from the PCB. Then reconnect it. Turn on the 
main power switch and repeat the Steps 1 to 4 described 
above. Confirm the display shows “Error found”. If the 
display shows “Error” or “Not connected” on the screen 
again, it is necessary to replace the panel for cassette 
(ECONAVI type) with a new one. 

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb   27

20/01/30   10:25:17

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

WarmPool DC55 Installation & Operation Manual preview
DC55
Бренд: WarmPool Страницы: 18
Panasonic CS-KS30NKU Technical & Service Manual preview
CS-KS30NKU
Бренд: Panasonic Страницы: 108
Panasonic CS-A12PKD Service Manual preview
CS-A12PKD
Бренд: Panasonic Страницы: 140
Magic-Pak EWC V Series Installation Instructions preview
EWC V Series
Бренд: Magic-Pak Страницы: 5
d2itsu APD-9CR User Manual preview
APD-9CR
Бренд: d2itsu Страницы: 20
Haier ESAD4089 Manual De Usuario preview
ESAD4089
Бренд: Haier Страницы: 26
Daikin FTKB09AXVJU Service Manual preview
FTKB09AXVJU
Бренд: Daikin Страницы: 84
Haier HWR05XC6 - 5200 BTU Electronic Control Room Air... User Manual preview
HWR05XC6 - 5200 BTU Electronic Control Room Air...
Бренд: Haier Страницы: 20
Klarstein Windsurfer User Manual preview
Windsurfer
Бренд: Klarstein Страницы: 28
Cooper & Hunter Arctic NG Wi-Fi Series Owner'S Manual preview
Arctic NG Wi-Fi Series
Бренд: Cooper & Hunter Страницы: 111
Friedrich KP05 Installation And Operation Manual preview
KP05
Бренд: Friedrich Страницы: 15
Movincool CLIMATE PRO 12 Manual preview
CLIMATE PRO 12
Бренд: Movincool Страницы: 50
Unitary products group 13 SEER TCGD12 - 60 SERIES Installation Manual preview
13 SEER TCGD12 - 60 SERIES
Бренд: Unitary products group Страницы: 12
Rotex RKHBH016AB Series Operation Manual preview
RKHBH016AB Series
Бренд: Rotex Страницы: 72
Nortek P8SD-X36C Installation Instructions Manual preview
P8SD-X36C
Бренд: Nortek Страницы: 16
McQuay IM-CKA-0501 A Series Installation Manual preview
IM-CKA-0501 A Series
Бренд: McQuay Страницы: 39
Daikin FVQ-C Technical Data Manual preview
FVQ-C
Бренд: Daikin Страницы: 13
Daikin CTXM15A2V1B Installer'S Reference Manual preview
CTXM15A2V1B
Бренд: Daikin Страницы: 60

Бренды по названию

Популярные бренды

Загрузить еще бренды