manualshive.com logo in svg

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Panasonic S-3650PF3E - Мощный и надежный продукт с выдающимися характеристиками. Теперь вы можете с легкостью узнать больше о его технических данных и обслуживании, скачав бесплатный руководство по эксплуатации с manualshive.com. Не упустите шанс загрузить его и улучшить свой пользовательский опыт.

Поделиться
Скачать
background image

1

1-11-1-2-14

(3)  See Table 1-11-1-2-2, 1-11-1-2-3 and Fig. 1-11-1-2-2 for details on the relationship between the value of item code “b0” and the 
      external static pressure.
(4)  When set in group control (connecting multiple indoor units with one wired remote controller), set each indoor unit to item code “b0”.
      When amending the setting after selecting [b. Manual setting] (due to airflow path changes, etc.), it is necessary to cancel [b. Manual 
      setting] (change the dip switch). When [b. Manual setting] has not been cancelled, [c. Manual setting] and [d. Auto airflow volume 
      setting] will be activated if selected, but [b. Manual setting] takes precedence when the power is switched back on after power 
      outages, etc.
(5)  If this is not completed within 8 minutes, check the operation mode, air speed and air inlet temperature.
(6)  When set in group control (connecting multiple indoor units with one wired remote controller), the test run operations display will 
      disappear once the external static pressure setting check or auto airflow volume control operation check have been completed for the
      main unit. However, it is not possible to determine whether sub-units have completed. The test run operation display will disappear 
      after one hour even if the external static pressure setting check or auto airflow volume control operation check have not been 
      completed.

 

CAUTION

  Be sure to check that the external static pressure is within the range for use and then make the setting. Failure to observe 

  this may result in insufficient airflow or water leakages. See Fig. 1-11-1-2-2 for the external static pressure setting range.

  There are cases in which automatic variable dampers and other mounted items may trigger the P12 alarm on systems that 

  modify the external static pressure when the auto airflow volume control operations or setting check operations are carried 

  out if high external static pressure is lowered. In this event, lower the dampers, etc., so that the external static pressure 

  reaches its lowest level, and then carry out the auto airflow volume control operations or setting check operations.

  Be sure to set the [External Static Pressure Setting] once again after amending the airflow path for the duct or air outlet after 

  setting the external static pressure.

  Set the air inlet temperature within the range for use. The auto airflow volume control will not function if the air inlet 

  temperature is over 45°C or if operation is other than fan mode.

How to Set on Indoor Unit Control PCB

Table 1-11-1-2-1

1. Turn off the power breaker to halt the supply of electricity to the indoor unit control PCB.
2. Open the electrical component box cover, then check the indoor unit control PCB. (Fig. 1-11-1-2-1)
3. Change the dip switch (SW001) of the indoor unit control PCB according to the setting selected in Table 1-11-1-2-1.

DIP switch

110 Pa

External static pressure at the 

time of rated airflow volume

TP6

TP3

TP1

1 2 3

ON

ON

50 Pa

TP6

1 2 3

TP3

TP1

ON

10 Pa

1 2 3

TP6

TP3

TP1

TP6

TP3

TP1

1

ON

3

2

TP6

TP3

TP1

3

2

1

SW001

Setting example

1: OFF

2: OFF

ON

3: ON

Indoor unit control PCB

Fig. 1-11-1-2-1

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb   14

20/01/30   10:25:50

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Panasonic CS-KS30NKU Technical & Service Manual preview
CS-KS30NKU
Бренд: Panasonic Страницы: 108
Panasonic CS-A12PKD Service Manual preview
CS-A12PKD
Бренд: Panasonic Страницы: 140
Zibro S1126 Operating Manual preview
S1126
Бренд: Zibro Страницы: 82
EUROM 380965 User Manual preview
380965
Бренд: EUROM Страницы: 28
York SUNLINE MAGNUM DJ 180 Technical Manual preview
SUNLINE MAGNUM DJ 180
Бренд: York Страницы: 40
Stulz SCS Series Installation, Operation And Maintenance Manual preview
SCS Series
Бренд: Stulz Страницы: 36
Stulz BNB1000 Installation, Operation & Maintanance Manual preview
BNB1000
Бренд: Stulz Страницы: 28
Airwell AWAU-YKD009-H11 Service Manual preview
AWAU-YKD009-H11
Бренд: Airwell Страницы: 80
Indel B Sleeping Well BACK Using And Installation Manual preview
Sleeping Well BACK
Бренд: Indel B Страницы: 54
Daikin RXS50J2V1B Installation Manual preview
RXS50J2V1B
Бренд: Daikin Страницы: 14
Daikin Altherma EPGA16DAV3 Installer'S Reference Manual preview
Altherma EPGA16DAV3
Бренд: Daikin Страницы: 100
Klimaire KSWM009-C113 Service Manual preview
KSWM009-C113
Бренд: Klimaire Страницы: 51
York Ultra Duct YUHA 18 FSAAAF Service Manual preview
Ultra Duct YUHA 18 FSAAAF
Бренд: York Страницы: 26
Toyotomi TGS-100FSA-E Installation And Operation Manual preview
TGS-100FSA-E
Бренд: Toyotomi Страницы: 24
Daikin MXS-E Technical Data Manual preview
MXS-E
Бренд: Daikin Страницы: 43
Alen AMS09 Installation Manual preview
AMS09
Бренд: Alen Страницы: 16
Gree SP-240A Operation Manual preview
SP-240A
Бренд: Gree Страницы: 26
mabe MMT12HABWCAM8 Owner'S Manual preview
MMT12HABWCAM8
Бренд: mabe Страницы: 100

Бренды по названию

Популярные бренды

Загрузить еще бренды