Panasonic S-3650PF3E Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 321

background image

1

1-11-1-2-17

* Setting at shipment

Operating the Timer Remote Controller

(CZ-RTC4)

Setting Item Code “

”

1. Press and hold down the

,

and

simultaneously for 4 or more seconds.

buttons

(
blink on the LCD display.)

, the Unit No., Item Code and Detailed Data will

2. The indoor unit numbers in the group control will be

3.

4.

5. Press the

button.

The display will stop blinking and remain illuminated.

6. Press the

button. The fan motor will stop operating

and the LCD display will return to the normal stop mode.

sequentially displayed whenever the Unit Select button is
pressed

.

Only the fan motor for the selected indoor unit will operate
during this time.

Specify the “

” item code by pressing the

/

buttons for the temperature setting buttons

and confirm the values.
(“

” set at shipment )

Press the

/

buttons for the time to amend the

values for the set data.
See Table 1-11-1-2-3 and Fig. 1-11-1-2-2 and select a
value between “

” and “

”.

Select “

” if the auto airflow volume setting is

activated.

1. Press and hold down the

button for 4 or more seconds.

“

Auto Airflow Volume Control Operations and External

Static Pressure Setting-Check Operation

” will be displayed on the LCD display.

2. Press the

button to start the test run.

3. Select the operation mode

(Fan) by pressing the

A

by pressing the

(Mode select) button.

d

e

e

p

s

n

a

f

e

h

t

t

c

e

l

e

s

n

e

h

T

(Fan speed) button.

4.

NOTE

Auto airflow volume control operations and external static

pressure setting-check operations will not be performed

unless the above settings are made.

5.

Table 1-11-1-2-3 Setting the external static pressure

The fan motor will be activated and auto airflow volume
control operations or external static pressure setting-check
operations will be started.
The power of the airflow will change while these operations
are in progress.
The external static pressure setting-check operations and
auto airflow volume control operations will be completed in
about 3 to 30 minutes.
“

” display will be disappeared from the LCD display.

Press the

button to halt the test run.

airﬂ

ow and condensation.

*

Failure to set this parameter may result in decreased

A

3

1, 6

4

5

1

2

A

°

°

1

3

2, 5

Indoor unit type

Item code

3650

6071

Outdoor unit type

–

150

External static pressure of the rated

airﬂ

ow volume (Pa)

140
130
120
110

90
70
50
30 *
10

No auto airﬂ

ow volume setting

A

uto airﬂ

ow volume setting

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 17

20/01/30 10:25:52

«
...
134
135
136
137
138
...
»

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Бренд: Jet Страницы: 14

Бренд: Valeo Страницы: 15

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 48

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 18

Бренд: Panasonic Страницы: 14

Бренд: Panasonic Страницы: 112

Бренд: Samsung Страницы: 40

Бренд: Omega Altise Страницы: 16

iCongo PSQ-08-01

Бренд: Soleus Air Страницы: 18

Бренд: Danby Страницы: 26

Бренд: Dyson Страницы: 36

Бренд: Levoit Страницы: 12

Comfort 50VL-C 24

Бренд: Carrier Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды