Panasonic S-3650PF3E Скачать руководство пользователя страница 311

Страница: 311 / 321

If a group of units are to be controlled by 2 remote controllers:

* Main/sub remote controllers will work regardless of which indoor

unit they are installed.

Use wiring of 0.5 mm

to 2 mm

for field supply.

Make the total wire length when cross-wiring a group no

more than 200 m.

When 1 indoor unit is operated by 2 remote controllers:

* Either of the remote controllers can be set to main/sub.

Use wiring of 0.5 mm

to 2 mm

for field supply.

Use a total wire length of no more than 400 m.

CN1

1 2

Wireless (Infrared) Remote

Controller Kit

Wired Remote Controller

(Sold Separately)

Receiver

(Sold Separately)

Remote Controller Wiring

(Field Supply)

Indoor Unit

* (Main)

* (Sub)

Wireless (Infrared) Remote

Controller Kit

1st Indoor

Unit

2nd Indoor

Unit

3rd Indoor

Unit

4th Indoor

Unit

* (Main)

* (Sub)

Cross-wiring Remote controllers for Group

Control (Field Supply)

Wired

Remote Controller

CN1

1 2

Installation when setting Main/Sub for the remote controller and the receiver

1 2

R1 R2

RC wiring (field supply)

•

No polarity

Indoor unit

1 2

R1 R2

Terminals for

RC wiring

)

(

)

(

)

(

)

(

Indoor unit



Using 1 indoor unit



Using more than 1 indoor unit

RC wiring

(field supply)

•

No polarity

Installation

example

After installation, according to the “Settings” section, set one to [Main] and the other to [Sub].
Setting the wired remote controller to [Main] is recommended.

Attention



Multiple wireless/(infrared) remote controllers cannot be used simultaneously for a single indoor unit.



Be careful not to connect cables to other terminals of indoor units (e.g. power source wiring terminal). Malfunction may occur.



Do not bundle together with the power source wiring or store in the same metal tube. Operation error may occur.



If noise is induced to the unit power supply, attach a noise filter.

* Wiring shown below is prohibited.

R1 R2

1 2

Wired RC

Receiver

Indoor unit

RC wiring

Receiver

The remote controller and the receiver can be connected to any indoor unit for operation.

8-3-2

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 2

20/01/14 10:04:20

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды