Panasonic S-3650PF3E Скачать руководство пользователя страница 291

Страница: 291 / 321

7-8. Test Run Function

Operates the unit with the thermostat forced ON.

<Procedure of CZ-RTC5B>

1 Keep pressing the

and

buttons simultaneously for 4 or more seconds.
The “Maintenance func” screen appears on the
LCD display.

2 Press the

button to see each

menu.
If you wish to see the next screen instantly, press
the

button.

Select "4. Test run" on the LCD display and press
the

button.

Change the display from OFF to ON by pressing
the

button. Then press the

button.

Fig. 7-8

Fig. 7-9

3 Press the

button. “TEST” will be displayed

on the LCD display.

4 Press the

button. Test run will be started.

Test run setting mode screen appears on the LCD
display.

CZ-RTC5B

CZ-RTC4

<Procedure of CZ-RTC4>

1 Press and hold the

button for 4 seconds or

longer.

2 “

” appears on the remote controller LCD

display (Fig. 7-9).

4 Press the

button to return to normal remote

controller display.

Press the

button to start the test run.

Maintenance func

Sel.

20:30 (THU)

1. Outdoor unit error data

2. Service contact

3. RC setting mode

4. Test run

Page [

] Confirm

Maintenance func

Sel.

Page [

] Confirm

20:30 (THU)

1. Outdoor unit error data

2. Service contact

3. RC setting mode

4. Test run

[

] Confirm

Test run

Change

20:30 (THU)

Test run

20:30 (THU)

[ ] START

TEST

[ ] START

20:30 (THU)

TEST

FAN SPEED

FLAP

20:30 (THU)

COOL

TEST

7-18

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 18

20/01/28 11:22:23

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды