Panasonic S-3650PF3E Скачать руководство пользователя страница 310 | Manualshive

Страница: 310 / 321

background image

8

8

8-3-1. Common to All Models

8-3. Wiring for the Receiver

1. Installation Location for the Receiver

The wireless (infrared) remote controllers use a very weak infrared light for its signal, which can result in the signal not being
received because of the following influences, so take care in where the unit is installed.

.

• Inverter or rapid-start type fluorescent lights. (Models with

out

glow lamps)

• Plasma display or LCD televisions.
• Direct sunlight or other sources of bright light.
Do not bundle together with the power source wiring or store in the same metal tube. Operation error may occur.
Be careful not to connect cables to other terminals of indoor units (e.g. power source wiring terminal). Malfunction may occur.

Avoid the following locations for installation.

• Location where condensation occurs
• Location where voltage fluctuation frequently occurs
• Location where there is a machine producing electromagnetic radiation

2. Installation location for the Wireless (Infrared) Remote Controller

If a remote controller is to be operated from a remote control holder that is hung on a wall, turn on the lights in the room as
well as any electrical appliances and then check to make sur

e the air conditioner works with the remote controller in the

location where it will be installed. If it works, continue with

installation.

If the main sensor is to be switched from the indoor unit to a

remote controller, pay attention to the following when installing.

• Locate where no warm or cold air will affect it.
• Locate in a place free from direct sunlight.
• Locate where it will not be affected by any other heat/cold

source.

8-3-1

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 1

20/01/14 10:04:20

«
...
308
309
310
311
312
...
»

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Бренд: Panasonic Страницы: 145

Бренд: Panasonic Страницы: 76

Бренд: Panasonic Страницы: 56

Бренд: Godrej Страницы: 50

Бренд: Gree Страницы: 73

Бренд: Zibro Страницы: 16

Бренд: GE Страницы: 28

Бренд: Daitsu Страницы: 56

Бренд: Airwell Страницы: 115

Бренд: Parker Страницы: 20

Altherma EHVZ-D9WG

Бренд: Daikin Страницы: 16

CS/CU-HU12ZKY Series

Бренд: Panasonic Страницы: 32

YDDN-22C(A/B)15A

Бренд: York Страницы: 12

YKGE48BXOXBH-RX

Бренд: York Страницы: 20

Бренд: York Страницы: 23

YVFVXH028WAR--GX

Бренд: York Страницы: 24

Бренд: York Страницы: 24

Бренд: York Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды