Panasonic S-3650PF3E Скачать руководство пользователя страница 320

Страница: 320 / 321

3
5

Address

ADR

Auto Address

Set the Auto Address for each O/D unit no. (outdoor unit number) Select the O/D unit no. for Auto Address.

1. Press for 4 seconds or longer.

• “ “ starts blinking and the setting screen is displayed.

2. Press to select the unit number (O/D unit no.)

from 1 to 30.

3. Press to set the Auto Address.

4. Press to check the Auto Address status.

(See the following table for the Auto Address status.)

• Proceed to step 5 when the status is “Completion” or “Error” .

• If “Running” keeps for 10 minutes or longer, check the unit number.

OPERATION TIMER STANDBY

: OFF, : ON (Illuminated),

◎

Blinking (0.5 seconds interval)

5. Press for 4 seconds or longer to exit the Auto Address setting.

• Auto Address setting is canceled while running or error occurring.

Set the Auto Address again after resolve the error cause if an error occurs.

• Set Auto address after all units are turned on and 90 seconds or more have passed.

• Operate the units after Auto address is set and 90 seconds or more have passed.

Auto

Address

Status

Buzzer

of the

receiver

Indication lamp on the receiver

Running

2 times

Completion 1 time

Error 5 times

8-3-11

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 11

20/01/14 10:04:23

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды