Panasonic S-3650PF3E Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 321

background image

1

1-11-1-1-20

(3) Installing the panel for cassette

The power must be turned ON in order to change the
flap angle. (Do not attempt to move the flap by hand.
Doing so may damage the flap.)

1) Hang the temporary latches on the inside of the panel

for cassette to the receptacle on the unit to temporarily
attach the panel for cassette in place.

The panel for cassette must be installed in the correct
direction relative to the unit. Align the REF. PIPE and
DRAIN marks on the panel for cassette corner with
the correct positions on the unit.

When removing the panel for cassette, push the
temporary latches outward while holding the panel for
cassette.

Receptacle on the

main unit

Push to disengage.

Temporary latch

Temporary latches (×2)

2) Align the panel installation holes and the unit screw

holes.

3) Tighten the provided washer head screws at the

4 panel installation locations so that the panel is
attached tightly to the unit.

4) Check that the panel is attached tightly to the ceiling.

At this time, make sure that there are no gaps
between the unit and the panel for cassette, or
between the panel for cassette and the ceiling surface.

If there is a gap between the panel and the ceiling,
leave the panel for cassette attached and make fine
adjustments to the installation height of the unit to
eliminate the gap with the ceiling.

CAUTION

If the screws are not sufficiently tightened, trouble
such as that shown in the figure below may occur.
Be sure to tighten the screws securely.

If a gap remains between the ceiling surface and the
panel for cassette even after the screws are tightened,
adjust the height of the unit again.

Make fine adjustment by a wrench or

other tools to the installation height

of the unit to eliminate the gap with

the ceiling through the holes of the

corner cover.

Do not allow gaps.

Panel for cassette

Main unit

Ceiling surface

Drain tube corner

Refrigerant tube

corner

Marking with DRAIN

Marking with REF. PIPE

Washer head screws

(preinstalled on the

panel for cassette)

Panel for cassette

Air leakage

Staining

Air leakage from

panel for cassette

Condensation, water leakage

Adjust so that there

are no gaps.

If there is no affect to the horizontal of the unit and

drain tube, adjustment to the installation height of the

unit can be made through the hole of the panel for

cassette corner.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 20

20/01/30 10:25:14

«
...
94
95
96
97
98
...
»

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Бренд: Panasonic Страницы: 122

Бренд: York Страницы: 32

Duct Type Series

Бренд: Samsung Страницы: 40

Бренд: WAGNER Страницы: 5

Бренд: UV CAN SANITIZE Страницы: 8

Бренд: Danby Страницы: 80

Бренд: Carrier Страницы: 54

WISE Parasol Zenith 600

Бренд: Swegon Страницы: 14

Sky Air B-Series R-410A

Бренд: Daikin Страницы: 338

Бренд: Kaysun Страницы: 64

Бренд: ARCTIC WIND Страницы: 16

Бренд: Refco Страницы: 8

Бренд: MrCool Страницы: 27

Бренд: Daikin Страницы: 23

Euro-Line AS28AL

Бренд: Argo Clima Страницы: 32

Бренд: Midea Страницы: 18

Бренд: Termal Страницы: 24

ProShield Plus Ai

Бренд: Oreck Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды