Panasonic S-3650PF3E Скачать руководство пользователя страница 2

Страница: 2 / 321

IMPORTANT!

Please Read Before Starting

WARNING

CAUTION

This air conditioner must be installed by the sales dealer

or installer.

This information is provided for use only by authorized

persons.

This Installation Instructions is for the indoor unit and

read the Installation Instructions of the outdoor unit as

well.

For safe installation and trouble-free operation, you

must:

Carefully read this instruction booklet before beginning.
This air conditioner is required to have the remote

controller which is adaptable to nanoe™X function.
Follow each installation or repair step exactly as shown.

This air conditioner shall be installed in accordance with

National Wiring Regulations.

That compliance with national gas regulations shall be

observed.
The product meets the technical requirements of

EN/IEC 61000-3-3.

Pay close attention to all warning and caution notices

given in this manual.

This symbol refers to a hazard or

unsafe practice which can result in

severe personal injury or death.
This symbol refers to a hazard or

unsafe practice which can result

in personal injury or product or

property damage.

If Necessary, Get Help

These instructions are all you need for most installation

sites and maintenance conditions. If you require help for

a special problem, contact our sales/service outlet or your

certified dealer for additional instructions.

In Case of Improper Installation

The manufacturer shall in no way be responsible for

improper installation or maintenance service, including

failure to follow the instructions in this document.

WARNING

Do not use means to accelerate

the defrosting process or to clean,

other than those recommended by

the manufacturer.

Auxiliary devices which may be a

potential ignition source

shall not

be installed in the duct work.

Examples of such

potential ignition

sources

are hot surfaces with a

temperature exceeding 700°C and

electric switching devices.

The appliance shall be stored

in a room without continuously

operating ignition sources (for

example: open flames, an operating

gas appliance or an operating

electric heater).

Do not pierce or burn.

For appliances connected via an

air duct system to one or more

rooms, only auxiliary devices

approved by the appliance

manufacturer or declared suitable

with the refrigerant shall be installed

in connecting ductwork.

Be aware that refrigerants may not

contain an odour.

The following checks shall be

applied to installations using

flammable refrigerants.

Appliance shall be installed,

operated and stored in a room with

a floor area larger than [Amin] m

As for [Amin], see the section

“CHECK OF DENSITY LIMIT”.

SPECIAL PRECAUTIONS

WARNING When Wiring

ELECTRICAL SHOCK CAN

CAUSE SEVERE PERSONAL

INJURY OR DEATH. ONLY A

QUALIFIED, EXPERIENCED

ELECTRICIAN SHOULD

ATTEMPT TO WIRE THIS

SYSTEM.

•

Do not supply power to the unit until

all wiring and tubing are completed or

reconnected and checked.

•

Highly dangerous electrical voltages are

used in this system. Carefully see the

wiring diagram and section 2 when wiring.

Improper connections and inadequate

grounding can cause

accidental injury

or death.

•

Connect all wiring tightly. Loose wiring

may cause overheating at connection

points and a possible fire hazard.

Provide a power outlet to be used

exclusively for each unit.

Provide a power outlet exclusively for

each unit, and full disconnection means

having a contact separation by 3 mm

in all poles must be incorporated in the

fixed wiring in accordance with the wiring

rules.
To prevent possible hazards from

insulation failure, the unit must be

grounded.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 1

2020/01/29 21:46:00

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды