Panasonic S-3650PF3E Скачать руководство пользователя страница 129

Страница: 129 / 321

1-11-1-2-10

1. Press and hold down the

and

(

buttons

, the Unit No., Item Code and Detailed Data

will blink on the LCD display.)

the

2. The indoor unit numbers in the group control will be

sequentially displayed whenever the Unit Select

button is pressed

Only the fan motor for the selected indoor unit will

operate during this time.

3. Specify the “

” item code by pressing

(“

buttons for the temperature setting buttons and

confirm the values.

” or “

4. Press the

values for the set data.

” set at shipment)

buttons for the time to amend the

“

”.

5. Press the

button.

The display will stop blinking and remain illuminated.

simultaneously for 4 or more seconds.

6. Specify the “

” item code by pressing the

and confirm the values. (“ ” set at shipment)

buttons for the temperature setting buttons

7. Press the

amend the values for the set data.

buttons for the time to

Select “

”.

8. Press the

button.

The display will stop blinking and remain

illuminated.

9. Press the

remote controller display.

button to return to normal

4, 7 5, 8

malfunction of the drain pump.

Operating the Timer Remote Controller

(CZ-RTC4)

Setting Item Code “ ” and “ ”

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 10

20/01/30 10:25:48

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды