Panasonic S-3650PF3E Скачать руководство пользователя страница 220

Страница: 220 / 321

4-15

4 4

T10 (CN061):

4-13. Indoor Unit Control PCB Switches and Functions

[Indoor unit control PCB]

6P plug (YEL)

/ Used for remote control operation. (See the Remote Control Section.)

Control items: (1) Start/stop input

(3) Start signal output

EXCT (CN073):

(2) Remote controller prohibit input

(4) Alarm signal output

DISP (CN062):

CHK (CN062):

JP1 (JP001):

Fan drive (CN032): 2P plug (WHT)

/ This terminal sends the signal to the ventilation fan when a commercially

Power LED:

EEPROM (IC010):

2P plug (RED)

/ Can be used for demand control. When input is present, forces the unit to

operate with the thermostat OFF.

6P plug (BLK)

2-5Pin / Short-circuiting this Pin allows operation to be controlled by the remote

controller even when an outdoor unit is not connected. (In this case, alarm “E04,” which

indicates trouble in the serial communication between the indoor and outdoor unit, does not

occur.)

6P plug (BLK)

1-4Pin / Test Pin. Short-circuiting this Pin allows the indoor FM (H fan speed),

drain pump

, ﬂap motor (F1 position), and electronic

expansion valve full-open position to be

checked.

However this function turns OFF if the indoor unit protection mechanism is activated.

The components will operate even if the remote controller and outdoor unit are not

connected, however the remote control cannot be used for control even if it is connected.

This Pin can be used for short-term tests.

Jumper wire

/ Allows selection of the T10 terminal start/stop signal. (See the Remote

Control Section.)

Setting at time of shipment: Pulse signal

Jumper wire cut: Static signal (continuous signal)

available ventilation fan is operated by the FAN button on the wired remote controller. (See

the Remote Control Section.)

Use a ventilation fan which can accept the no-voltage contact A signal as the external input

signal.

LED (RED)

/ Illuminates when the power is ON. Flashes when there is trouble with the

EEPROM (IC010: nonvolatile memory).

Nonvolatile memory

/ Used to store model information and other data. When replacing

the PCB, remove the EEPROM from the old PCB and install it onto the new PCB. If there is

IC trouble, replace with a new IC (provided with the servicing PCB), and set the necessary

information using the wired remote controller. (For the setting procedure, see the servicing

technical materials.)

Type U3, Type F3

Connection cable between

outdoor and indoor unit

Power supply cable

■

JP001

EXCT (CN073)

FAN DRIVE (CN032)

EEPROM (IC010)

DISP

CHK (CN062)

T10 (CN061)

ACXA73-3129* : 4-Way Cassette Type (Type U3) Indoor Unit Control Board

ACXA73-3440* : Middle Static Pressure Duct Type (Type F3) Indoor Unit Control Board

OPTION (CN060)

POWER LED (D002)

JP001

EXCT (CN073)

FAN DRIVE (CN032)

EEPROM (IC010)

DISP

CHK (CN062)

T10 (CN061)

OPTION (CN060)

POWER LED (D002)

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 15

2020/01/30 13:58:48

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды